summaryrefslogtreecommitdiffstats
path: root/build_tools/clarch/larch/profiles
diff options
context:
space:
mode:
Diffstat (limited to 'build_tools/clarch/larch/profiles')
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/addedpacks145
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/baseveto7
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/cache_packs35
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/cd-root/isolinux/isolinux.cfg38
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/cd-root/isolinux/vbg.jpgbin0 -> 57322 bytes
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/locale.gen8
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/mkinitcpio.conf54
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/pacman.conf66
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/pkglist366
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/post-process.sh17
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/post_process/fstab14
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/post_process/functions.patch13
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/post_process/hosts.allow7
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/post_process/hosts.deny6
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/post_process/menu.lst55
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/post_process/pacman.conf64
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/post_process/rc.conf113
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/post_process/rc.local21
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/post_process/rc.shutdown104
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/post_process/rc.sysinit.patch14
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/post_process/root13
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/post_process/securetty19
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/post_process/tweak.sh67
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/rcconfx16
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/conf.d/dhcpcd6
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/hosts.allow7
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/inittab42
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/larch-shutdown47
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/ppp/options352
-rwxr-xr-xbuild_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/rc.local21
-rw-r--r--build_tools/clarch/larch/profiles/MV-local/rootoverlay/root/.bashrc2
31 files changed, 1739 insertions, 0 deletions
diff --git a/build_tools/clarch/larch/profiles/MV-local/addedpacks b/build_tools/clarch/larch/profiles/MV-local/addedpacks
new file mode 100644
index 0000000..f518409
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/addedpacks
@@ -0,0 +1,145 @@
+# These are needed to build a live CD
+linhes-live
+squashfs-tools
+lzop
+
+syslinux
+
+# You need a kernel.
+#kernel26 is now in 'base'
+aufs
+
+# To eject a cd
+eject
+
+# Useful for use as installer, etc.
+ntfsprogs
+parted
+#ddcxinfo-knoppix
+#hwd
+
+# generally useful tools which don't require X
+openssh
+dosfstools
+lynx
+#mc
+unzip
+zip
+
+lsof
+#cdrkit
+#dvd+rw-tools
+
+etcnet
+
+xorg
+xorg-xinit
+#xf86-video-amd
+xf86-video-apm
+xf86-video-ark
+xf86-video-ati
+xf86-video-chips
+xf86-video-cirrus
+xf86-video-dummy
+xf86-video-fbdev
+xf86-video-glint
+xf86-video-i128
+xf86-video-i740
+#xf86-video-i810
+xf86-video-imstt
+xf86-video-intel
+xf86-video-mga
+xf86-video-neomagic
+xf86-video-nv
+#xf86-video-radeonhd
+xf86-video-rendition
+xf86-video-s3
+xf86-video-s3virge
+xf86-video-savage
+xf86-video-siliconmotion
+xf86-video-sis
+xf86-video-sisusb
+#xf86-video-tdfx
+xf86-video-trident
+xf86-video-tseng
+xf86-video-v4l
+xf86-video-vesa
+xf86-video-vga
+xf86-video-vmware
+xf86-video-voodoo
+nvidia
+
+
+
+
+
+#terminal
+openssh
+ntp
+runit
+runit-scripts-mv
+mysql
+
+mythtv-release-fixes
+mythtv-themes-release-fixes
+mediadirsetup
+lm_sensors
+MythVantage-mythmenu
+setserial
+avahi
+keylaunch
+mysql-python
+acpid
+
+
+tilda
+#opera
+ivtv-utils
+hd3000firmware
+oss-linux-free
+alsa-utils
+
+make
+python-iplib
+#hdhgrab
+hdhomerun
+
+#intel-e1000
+perl-dbi
+perl-dbd-mysql
+lcdproc
+netkit-telnet
+nfs-utils
+jfsutils
+xfsprogs
+
+patch
+gdb
+sudo
+syslog-ng
+
+ttf-bitstream-vera
+xine-lib
+
+#syth-lacquer-wide
+#Midnight-wide
+#Midnight-blue
+#basic-blue
+#basic-green
+#basic-amber
+#basic-purple
+#basic-red
+
+
+MythVantage-system
+#live-installer
+MythVantage-config
+libstatgrab
+nmbscan
+smbclient
+
+
+
+enlightenment
+e16-myth-settings
+ttf-ms-fonts
diff --git a/build_tools/clarch/larch/profiles/MV-local/baseveto b/build_tools/clarch/larch/profiles/MV-local/baseveto
new file mode 100644
index 0000000..419aad4
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/baseveto
@@ -0,0 +1,7 @@
+xfsprogs
+xfsdump
+jfsutils
+kernel26STB
+xf86-video-unichrome
+xf86-video-via
+
diff --git a/build_tools/clarch/larch/profiles/MV-local/cache_packs b/build_tools/clarch/larch/profiles/MV-local/cache_packs
new file mode 100644
index 0000000..ee33030
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/cache_packs
@@ -0,0 +1,35 @@
+#comment
+xosd
+local-website
+webcalendar
+lighttpd
+mythdb-initial
+samba
+libmysqlclient
+mysql
+hobbitserver
+hobbit-client
+dnsmasq
+mysql-clients
+mythtv-status
+avahi
+dbus
+myth2ipod
+tightvnc
+phpmyadmin
+libgl-dri
+mythphone-release-fixes
+mytharchive-release-fixes
+mythbrowser-release-fixes
+mythnews-release-fixes
+mythgame-release-fixes
+mythflix-release-fixes
+mythweather-release-fixes
+mythcontrols-release-fixes
+mythgallery-release-fixes
+mythmovietime-release-fixes
+mythmusic-release-fixes
+mythsmolt-release-fixes
+mythvideo-release-fixes
+mythweb-release-fixes
+alsa-lib
diff --git a/build_tools/clarch/larch/profiles/MV-local/cd-root/isolinux/isolinux.cfg b/build_tools/clarch/larch/profiles/MV-local/cd-root/isolinux/isolinux.cfg
new file mode 100644
index 0000000..6686db4
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/cd-root/isolinux/isolinux.cfg
@@ -0,0 +1,38 @@
+PROMPT 0
+TIMEOUT 40
+DEFAULT vesamenu.c32
+MENU BACKGROUND vbg.jpg
+MENU TITLE MythVantage Boot options
+MENU COLOR border 31;40 #90ffff00 #00000000 std
+MENU COLOR sel 31;47 #00000000 #FFFFFF15 all
+
+
+LABEL MythVantage
+KERNEL vmlinuz
+APPEND vga=normal initrd=larch.img noauto
+
+LABEL MythVantage-NoX
+KERNEL vmlinuz
+APPEND vga=normal initrd=larch.img noauto NoX
+
+LABEL MythVantage-Vnc
+KERNEL vmlinuz
+APPEND vga=normal initrd=larch.img noauto vnc ip=192.168.1.222 netdev=eth0
+
+LABEL MythVantage-dhcp
+KERNEL vmlinuz
+APPEND vga=normal initrd=larch.img noauto ip=dhcp netdev=eth0
+
+LABEL MythVantage-remote
+APPEND vga=normal initrd=larch.img noauto ip=dhcp remote=MX-500-jams remoteport=ttyS0
+
+LABEL MythVantage-static-ip
+KERNEL vmlinuz
+APPEND vga=normal initrd=larch.img noauto vnc ip=192.168.1.222 netmask=255.255.0.0 gateway=192.168.1.1 netdev=eth0 dns=192.168.1.1
+
+LABEL Boot_from_hardrive
+ localboot 0xffff
+
+
+MENU ROWS 6
+
diff --git a/build_tools/clarch/larch/profiles/MV-local/cd-root/isolinux/vbg.jpg b/build_tools/clarch/larch/profiles/MV-local/cd-root/isolinux/vbg.jpg
new file mode 100644
index 0000000..d9f3ebb
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/cd-root/isolinux/vbg.jpg
Binary files differ
diff --git a/build_tools/clarch/larch/profiles/MV-local/locale.gen b/build_tools/clarch/larch/profiles/MV-local/locale.gen
new file mode 100644
index 0000000..a3276b1
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/locale.gen
@@ -0,0 +1,8 @@
+# locales for larch (/etc/locale.gen)
+
+en_US ISO-8859-1
+en_US.UTF-8 UTF-8
+de_DE ISO-8859-1
+de_DE@euro ISO-8859-15
+de_DE.UTF-8 UTF-8
+
diff --git a/build_tools/clarch/larch/profiles/MV-local/mkinitcpio.conf b/build_tools/clarch/larch/profiles/MV-local/mkinitcpio.conf
new file mode 100644
index 0000000..f26fdb1
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/mkinitcpio.conf
@@ -0,0 +1,54 @@
+# vim:set ft=sh
+# MODULES
+# The following modules are loaded before any boot hooks are
+# run. Advanced users may wish to specify all system modules
+# in this array. For instance:
+# MODULES="piix ide_disk reiserfs"
+MODULES=""
+
+# BINARIES
+# This setting includes, into the CPIO image, and additional
+# binaries a given user may wish. This is run first, so may
+# be used to override the actual binaries used in a given hook.
+# (Existing files are NOT overwritten is already added)
+# BINARIES are dependancy parsed, so you may safely ignore libraries
+#BINARIES=""
+
+# FILES
+# This setting is similar to BINARIES above, however, files are added
+# as-is and are not parsed in anyway. This is useful for config files.
+# Some users may wish to include modprobe.conf for custom module options,
+# like so:
+# FILES="/etc/modprobe.conf"
+FILES=""
+
+# HOOKS
+# This is the most important setting in this file. The HOOKS control the
+# modules and scripts added to the image, and what happens at boot time.
+# Order is important, and it is recommended that you do not change the
+# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
+# help on a given hook.
+# 'base' is _required_ unless you know precisely what you are doing.
+# 'udev' is _required_ in order to automatically load modules
+# 'modload' may be used in place of 'udev', but is not recommended
+# 'filesystems' is _required_ unless you specify your fs modules in MODULES
+# Examples:
+# This setup specifies all modules in the MODULES setting above.
+# No raid, lvm, or encrypted root is needed.
+# HOOKS="base"
+#
+# This setup will autodetect all modules for your system and should
+# work as a sane default
+# HOOKS="base udev autodetect ide scsi sata filesystems"
+#
+# This setup will generate a 'full' image which supports most systems.
+# No autodetection is done.
+# HOOKS="base udev ide scsi sata usb filesystems"
+#
+# This setup assembles an ide raid array with an encrypted root FS.
+# Note: See 'mkinitcpio -H raid' for more information on raid devices.
+# HOOKS="base udev ide filesystems raid encrypt"
+#
+# This setup loads an LVM volume group on a usb device.
+# HOOKS="base udev usb filesystems lvm"
+HOOKS="base udev ide scsi sata usb larch1 larch2___aufs___ larch3"
diff --git a/build_tools/clarch/larch/profiles/MV-local/pacman.conf b/build_tools/clarch/larch/profiles/MV-local/pacman.conf
new file mode 100755
index 0000000..3739bbc
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/pacman.conf
@@ -0,0 +1,66 @@
+#
+# /etc/pacman.conf
+# from pacman.conf MV
+# NOTE: If you find a mirror that is geographically close to you, please
+# move it to the top of the server list, so pacman will choose it
+# first.
+#
+# To re-sort your mirror lists by ping/traceroute results, use the
+# /usr/bin/sortmirrors script. It requires the "netselect" package.
+#
+
+# See the pacman manpage for option directives
+
+#
+# GENERAL OPTIONS
+#
+[options]
+LogFile = /var/log/pacman.log
+NoUpgrade = etc/passwd etc/group etc/shadow etc/sudoers
+NoUpgrade = etc/fstab etc/raidtab etc/ld.so.conf
+NoUpgrade = etc/rc.conf etc/rc.local
+NoUpgrade = etc/modprobe.conf etc/modules.conf
+NoUpgrade = etc/lilo.conf boot/grub/menu.lst
+NoUpgrade = data/srv/hobbit/etc/bb-hosts
+NoUpgrade = etc/func/minion.conf
+
+HoldPkg = pacman glibc
+CacheDir = /data/var/cache/pacman/pkg
+#XferCommand = /usr/bin/wget --passive-ftp -c -O %o %u
+
+#
+# REPOSITORIES
+# - can be defined here or included from another file
+# - pacman will search repositories in the order defined here.
+# - local/custom mirrors can be added here or in separate files
+#
+[mv-core]
+Server = http://localmirror/repo/i686/mv-core
+
+[core-testing]
+#Server = file:///data/local/pkg_repo/i686/core-testing
+Server = http://localmirror/repo/i686/core-testing
+
+[extra-testing]
+#Server = file:///data/local/pkg_repo/i686/core-testing
+Server = http://localmirror/repo/i686/extra-testing
+
+
+########################ARCH DEFAULTS#############
+#[core]
+# Add your preferred servers here, they will be used first
+#Include = /etc/pacman.d/mirrorlist
+
+#[extra]
+# Add your preferred servers here, they will be used first
+#Include = /etc/pacman.d/mirrorlist
+
+#[community]
+# Add your preferred servers here, they will be used first
+#Include = /etc/pacman.d/mirrorlist
+
+# Unstable is disabled by default. To enable, uncomment the following
+# two lines. You can add preferred servers immediately after the header,
+# and they will be used before the default mirrors.
+#[unstable]
+#Include = /etc/pacman.d/mirrorlist
diff --git a/build_tools/clarch/larch/profiles/MV-local/pkglist b/build_tools/clarch/larch/profiles/MV-local/pkglist
new file mode 100644
index 0000000..91351bc
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/pkglist
@@ -0,0 +1,366 @@
+Midnight-blue 1-22
+Midnight-wide 1-22
+STB-mythmenu 1.0-38
+STB-system 3.0-159
+acl 2.2.47-1
+acpid 1.0.6-3
+alsa-lib 1.0.16-1
+atk 1.22.0-1
+attr 2.4.41-1
+audiofile 0.2.6-3
+avahi 0.6.22-1
+bash 3.2.033-2
+basic-amber 1-5
+basic-blue 1-6
+basic-green 1-5
+basic-purple 1-5
+basic-red 1-5
+bc 1.06-4
+bigreqsproto 1.0.2-1
+binutils 2.18-8
+bzip2 1.0.5-2
+ca-certificates 20080514-3
+cairo 1.6.4-1
+compositeproto 0.4-1
+confuse 2.5-1
+coreutils 6.12-1
+cpio 2.9-3
+cracklib 2.8.10-5
+cryptsetup 1.0.6-1
+curl 7.18.2-1
+damageproto 1.1.0-1
+dash 0.5.4-4
+db 4.6.21-2
+dbus 1.2.1-1
+dbus-glib 0.76-1
+dcron 3.2-3
+ddcxinfo-arch 0.8-1
+device-mapper 1.02.24-1
+dhcpcd 3.2.1-1
+dialog 1.1_20080316-3
+diffutils 2.8.1-5
+dmapi 2.2.8-3
+dmidecode 2.9-2
+dmxproto 2.2.2-1
+dnsutils 9.4.2-1
+e16-myth-settings 1.0-38
+e2fsprogs 1.40.8-1
+ed 0.9-1
+eject 2.1.5-3
+enlightenment 0.16.8.9-2
+esd 0.2.38-3
+etcnet 0.7.15-19
+ethtool 6-1
+evilwm 1.0.0-1.1
+exo 0.3.4-1
+expat 2.0.1-1
+expect 5.44.1.4-1
+file 4.24-1
+filesystem 2008.06-2
+findutils 4.4.0-1
+fixesproto 4.0-2
+flac 1.2.1-1
+fontcacheproto 0.1.2-1
+fontconfig 2.5.0-1
+fontsproto 2.0.2-1
+freetype2 2.3.6-1
+func 0.13-15
+gawk 3.1.6-2
+gcc 4.3.1-1
+gcc-libs 4.3.1-1
+gdb 6.8-1
+gdbm 1.8.3-5
+gdk-pixbuf 0.22.0-4
+gen-init-cpio 2.6.17-3
+gettext 0.17-1
+ghosd 0.0.1-18
+glib 1.2.10-7
+glib2 2.16.4-1
+glibc 2.8-2
+glproto 1.4.9-1
+gmp 4.2.2-2
+grep 2.5.3-3
+groff 1.19.2-4
+grub 0.97-12
+gtk 1.2.10-8
+gtk2 2.12.10-1
+guile 1.8.4-2
+gzip 1.3.12-4
+hal 0.5.11-1
+hal-info 0.20080508-1
+hd3000firmware 0.1-1
+hdhgrab 1-1
+hdhomerun 20070726-1
+hdparm 8.6-1
+heimdal 1.0.1-2
+hwd 5.3.4-1
+hwdetect 0.9-1
+iguanaIR 0.95-3
+imlib2 1.4.1-1
+initscripts 2008.05-1
+inputproto 1.4.3-1
+intel-dri 7.0.3-1
+intel-e1000 7.6.15.4-2
+iproute 2.6.24_rc7-1
+iptables 1.4.0-2
+iputils 20070202-4
+ivtv-utils 1.0.3-1
+jfsutils 1.1.12-2
+kbd 1.14.1.20080309-2
+kbproto 1.0.3-1
+kernel-headers 2.6.25.6-1
+kernel26STB 2.6.24-39
+keylaunch 1.3.3-10
+klibc 1.5-5
+klibc-extras 2.4-1
+klibc-kbd 1.15.20080312-5
+klibc-module-init-tools 3.2.2-3
+klibc-udev 116-3
+lame 3.98-1
+lcdproc 20080326-7
+less 418-1
+libarchive 2.5.5-1
+libavc1394 0.5.3-1
+libcap 1.10-2
+libdaemon 0.12-1
+libdatrie 0.1.2-1
+libdc1394 2.0.1-1
+libdmx 1.0.2-1
+libdownload 1.3-1
+libdrm 2.3.0-1
+libfontenc 1.0.4-1
+libgcrypt 1.4.1-1
+libglade 2.6.2-1
+libgpg-error 1.6-1
+libice 1.0.4-1
+libid3tag 0.15.1b-2
+libiec61883 1.1.0-1
+libjpeg 6b-4
+liblbxutil 1.0.1-1
+libldap 2.3.40-1
+libmng 1.0.10-1
+libmpeg2 0.4.1-1
+libmysqlclient 5.0.60-1
+libogg 1.1.3-1
+libpcap 0.9.8-2
+libpng 1.2.29-1
+libraw1394 1.3.0-1
+libsasl 2.1.22-5
+libsm 1.0.3-1
+libsmbios 2.0.2-1
+libstatgrab 0.14-1
+libthai 0.1.9-1
+libtheora 1.0beta1-1
+libtiff 3.8.2-3
+libtool 2.2.4-1
+libungif 4.1.4-1
+libusb 0.1.12-3
+libvorbis 1.2.0-1
+libx11 1.1.4-2
+libx86 0.99-1
+libxau 1.0.3-1
+libxaw 1.0.4-1
+libxcb 1.1-1
+libxcomposite 0.4.0-1
+libxcursor 1.1.9-1
+libxdamage 1.1.1-1
+libxdmcp 1.0.2-1
+libxext 1.0.4-1
+libxfce4util 4.4.2-1
+libxfixes 4.0.3-1
+libxfont 1.3.2-1
+libxfontcache 1.0.4-1
+libxft 2.1.12-1
+libxi 1.1.3-1
+libxinerama 1.0.3-1
+libxkbfile 1.0.5-1
+libxkbui 1.0.2-1
+libxml2 2.6.32-1
+libxmu 1.0.4-1
+libxp 1.0.0-1
+libxpm 3.5.7-1
+libxrandr 1.2.2-1
+libxrender 0.9.4-1
+libxt 1.0.5-1
+libxtrap 1.0.0-1
+libxtst 1.0.3-1
+libxv 1.0.4-1
+libxvmc 1.0.4-1
+libxxf86dga 1.0.2-1
+libxxf86misc 1.0.1-1
+libxxf86vm 1.0.1-1
+licenses 2.4-1
+lirc 0.8.3-17
+lirc-utils 0.8.3-13
+live-installer 3.2-52
+lm_sensors 3.0.2-1
+logrotate 3.7.5-1
+lvm2 2.02.36-1
+lzo2 2.02-3
+mailx 8.1.1-5
+man 1.6f-2
+man-pages 3.00-1
+mcpp 2.6.4-2
+mdadm 2.6.4-1
+mediadirsetup 1-14
+mesa 7.0.3-3
+mkinitcpio 0.5.19-1
+mlocate 0.20-2
+module-init-tools 3.2.2-6
+mpfr 2.3.1-1
+mysql 5.0.60-200
+mysql-clients 5.0.60-1
+mysql-python 1.2.2-1
+mythtv-release-fixes 17773-8
+mythtv-themes-release-fixes 15931-4
+nano 2.0.7-1
+ncid 0.71-1
+ncurses 5.6-6
+net-tools 1.60-13
+netkit-telnet 0.17-7
+nfs-utils 1.1.0-2
+nfsidmap 0.20-2
+nmbscan 1.2.5-1
+ntp 4.2.4p4-1
+nvidia-STB 173.08-5
+nvidia-utils 173.08-4
+openssh 5.0p1-1
+openssl 0.9.8h-3
+opera 9.51-1
+oss 4.0_1016-11
+pacman 3.2.0-2008
+pam 1.0.1-1
+pango 1.18.4-3
+patch 2.5.9-1
+pciutils 2.2.8-3
+pcmciautils 014-4
+pcre 7.7-1
+perl 5.10.0-3
+perl-date-manip 5.44-1
+perl-dbd-mysql 3.0008-11000
+perl-dbi 1.601-1
+perl-uri 1.35-3
+perl-xml-parser 2.34-2
+pixman 0.10.0-1
+pm-utils 1.1.2.2-1
+popt 1.10.6-3
+portmap 6.0-2
+ppp 2.4.4-6
+printproto 1.0.4-1
+procinfo 19-2
+procps 3.2.7-1000
+psmisc 22.6-1
+pyopenssl 0.6-3
+python 2.5.2-2
+python-iplib 1.0-1
+qt3 3.3.8-7
+randrproto 1.2.1-1
+readline 5.2-7
+recordproto 1.13.2-1
+reiserfsprogs 3.6.20-3
+renderproto 0.9.3-1
+rp-pppoe 3.8-3
+run-parts 2.28.6-2
+runit 1.8.0-32
+sdl 1.2.13-1
+sdparm 1.02-2
+sed 4.1.5-3
+setserial 2.17-2
+shadow 4.0.18.2-2
+smbclient 3.0.30-1
+sudo 1.6.9p17-1
+swig 1.3.31-1
+sysfsutils 2.1.0-4
+syslog-ng 2.0.9-4
+sysvinit 2.86-4
+syth-lacquer-wide 4-1
+tar 1.20-2
+tcl 8.5.3-1
+tcp_wrappers 7.6-8
+terminal 0.2.8-2
+tilda 0.9.6-8
+trapproto 3.4.3-1
+ttf-bitstream-vera 1.10-5
+tzdata 2008c-1
+udev 119-1
+unclutter 8-1
+unichrome-dri 7.0.3-1
+usbutils 0.73-5
+util-linux-ng 2.13.0.1-2
+vbetool 1.0-2
+vi 7.1.330-1
+videoproto 2.2.2-1
+vmwaretools 6.0.0-6
+vte 0.16.14-1
+wavpack 4.50.0-1
+wget 1.11.3-1
+which 2.19-2
+wireless_tools 29-2
+wol 0.7.1-2
+wpa_supplicant 0.5.10-1
+xbitmaps 1.0.1-1
+xcb-proto 1.1-1
+xcursor-themes 1.0.1-1
+xextproto 7.0.3-1
+xf86-input-evdev 2.0.1-1
+xf86-input-joystick 1.3.1-1
+xf86-input-keyboard 1.3.1-1
+xf86-input-mouse 1.2.3-1
+xf86-video-apm 1.2.0-1
+xf86-video-ark 0.7.0-1
+xf86-video-ati 6.8.0-4
+xf86-video-chips 1.2.0-1
+xf86-video-cirrus 1.2.1-1
+xf86-video-dummy 0.2.0-4
+xf86-video-fbdev 0.3.1-4
+xf86-video-glint 1.1.1-5
+xf86-video-i128 1.2.1-4
+xf86-video-i740 1.1.0-4
+xf86-video-imstt 1.1.0-4
+xf86-video-intel 2.3.2-1
+xf86-video-mga 1.4.8-3
+xf86-video-neomagic 1.2.1-1
+xf86-video-nv 2.1.9-1
+xf86-video-rendition 4.1.3-4
+xf86-video-s3 0.5.0-4
+xf86-video-s3virge 1.10.1-1
+xf86-video-savage 2.2.1-1
+xf86-video-siliconmotion 1.5.1-4
+xf86-video-sis 0.9.4-3
+xf86-video-sisusb 0.8.1-4
+xf86-video-tdfx 1.4.0-1
+xf86-video-trident 1.3.0-2
+xf86-video-tseng 1.1.1-4
+xf86-video-v4l 0.1.1-4
+xf86-video-vesa 1.3.0-5
+xf86-video-vga 4.1.0-4
+xf86-video-via 0.2.2-5
+xf86-video-vmware 10.16.2-1
+xf86-video-voodoo 1.1.1-4
+xf86dgaproto 2.0.3-1
+xf86miscproto 0.9.2-1
+xf86vidmodeproto 2.2.2-1
+xfsprogs 2.9.7-1
+xine-lib 1.1.12-1
+xineramaproto 1.1.2-1
+xkeyboard-config 1.2-1
+xorg-apps 1.0.3-3
+xorg-font-utils 1.0.3-3
+xorg-fonts-100dpi 1.0.1-1
+xorg-fonts-75dpi 1.0.1-2
+xorg-fonts-alias 1.0.1-1
+xorg-fonts-encodings 1.0.2-2
+xorg-fonts-misc 1.0.0-3
+xorg-res-utils 1.0.3-2
+xorg-server 1.4.2-10
+xorg-server-utils 7.3-1
+xorg-twm 1.0.1-2
+xorg-utils 7.3-1
+xorg-xauth 1.0.2-1
+xorg-xinit 1.1.0-1
+xorg-xkb-utils 1.0.2-2
+xosd 2.2.14-1
+xproto 7.0.13-1
+xterm 235-1
+xtrans 1.2-1
+zlib 1.2.3-4
diff --git a/build_tools/clarch/larch/profiles/MV-local/post-process.sh b/build_tools/clarch/larch/profiles/MV-local/post-process.sh
new file mode 100755
index 0000000..131b907
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post-process.sh
@@ -0,0 +1,17 @@
+#!/bin/bash
+echo $@
+INSTDIR=$1
+PROFILE=$2
+
+#everything below this point is specific to MythVantage
+cp -rp $PROFILE/post_process $INSTDIR/.tweak
+chroot $INSTDIR .tweak/tweak.sh
+rm -rf $INSTDIR/.tweak
+
+#find the size of the install.
+#This is used to calculate progress on the install
+tsize=`du -sm $INSTDIR/ | cut -f1`
+echo "TOTALSIZE=$tsize" > $INSTDIR/root/.install_size
+upsize=`du -sm --exclude data $INSTDIR/ |cut -f1`
+echo "UPGRADESIZE=$upsize" >> $INSTDIR/root/.install_size
+
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/fstab b/build_tools/clarch/larch/profiles/MV-local/post_process/fstab
new file mode 100755
index 0000000..8ea8305
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/fstab
@@ -0,0 +1,14 @@
+#
+# /etc/fstab: static file system information
+#
+# <file system> <dir> <type> <options> <dump> <pass>
+none /dev/pts devpts defaults 0 0
+none /dev/shm tmpfs defaults 0 0
+
+/dev/cdrom /mnt/cd iso9660 ro,user,noauto,unhide 0 0
+/dev/dvd /mnt/dvd udf ro,user,noauto,unhide 0 0
+/dev/fd0 /mnt/fl vfat user,noauto 0 0
+
+/dev/hda1 / reiserfs defaults 0 1
+/dev/hda2 swap swap defaults 0 0
+/dev/hda3 /data reiserfs defaults 0 0
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/functions.patch b/build_tools/clarch/larch/profiles/MV-local/post_process/functions.patch
new file mode 100644
index 0000000..eb9034c
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/functions.patch
@@ -0,0 +1,13 @@
+--- functions.orig 2008-07-06 10:16:37.000000000 -0500
++++ functions 2008-07-06 19:42:07.000000000 -0500
+@@ -61,8 +61,8 @@
+
+ # prefixes:
+
+-PREFIX_REG="::"
+-PREFIX_HL=" >"
++PREFIX_REG=" :"
++PREFIX_HL=" :"
+
+ # functions:
+
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/hosts.allow b/build_tools/clarch/larch/profiles/MV-local/post_process/hosts.allow
new file mode 100644
index 0000000..ca19dbb
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/hosts.allow
@@ -0,0 +1,7 @@
+#
+# /etc/hosts.allow
+#
+ALL: 192.168.
+ALL: 10.
+ALL: 127.0.0.1
+# End of file
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/hosts.deny b/build_tools/clarch/larch/profiles/MV-local/post_process/hosts.deny
new file mode 100755
index 0000000..ca30ab4
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/hosts.deny
@@ -0,0 +1,6 @@
+#
+# /etc/hosts.deny
+#
+ALL
+
+# End of file
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/menu.lst b/build_tools/clarch/larch/profiles/MV-local/post_process/menu.lst
new file mode 100755
index 0000000..1bd45a6
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/menu.lst
@@ -0,0 +1,55 @@
+# Config file for GRUB - The GNU GRand Unified Bootloader
+# /boot/grub/menu.lst
+
+# DEVICE NAME CONVERSIONS
+#
+# Linux Grub
+# -------------------------
+# /dev/fd0 (fd0)
+# /dev/hda (hd0)
+# /dev/hdb2 (hd1,1)
+# /dev/hda3 (hd0,2)
+#
+
+# FRAMEBUFFER RESOLUTION SETTINGS
+# +-------------------------------------------------+
+# | 640x480 800x600 1024x768 1280x1024
+# ----+--------------------------------------------
+# 256 | 0x301=769 0x303=771 0x305=773 0x307=775
+# 32K | 0x310=784 0x313=787 0x316=790 0x319=793
+# 64K | 0x311=785 0x314=788 0x317=791 0x31A=794
+# 16M | 0x312=786 0x315=789 0x318=792 0x31B=795
+# +-------------------------------------------------+
+
+# general configuration:
+timeout 5
+default 0
+#color light-blue/black light-cyan/blue
+
+# boot sections follow
+# each is implicitly numbered from 0 in the order of appearance below
+#
+# TIP: If you want a 1024x768 framebuffer, add "vga=773" to your kernel line.
+#
+#-*
+hiddenmenu
+
+# (0) normal
+title MythVantage
+root (hd0,0)
+kernel /boot/vmlinuz26 root=/dev/hda1 ro init=/sbin/runit console=tty1
+initrd /boot/kernel26.img
+
+# (1) bootsplash
+title STB-bootsplash
+root (hd0,0)
+kernel /boot/vmlinuz26 root=/dev/hda1 ro init=/sbin/runit quiet vga=0x318 splash=silent,theme:darch console=tty1
+initrd /boot/kernel26.img
+
+# (2) noautologin
+title STB-nologin
+root (hd0,0)
+kernel /boot/vmlinuz26 root=/dev/hda1 ro init=/sbin/runit quiet vga=0x318 splash=silent,theme:darch console=tty1 noautologin
+initrd /boot/kernel26.img
+
+
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/pacman.conf b/build_tools/clarch/larch/profiles/MV-local/post_process/pacman.conf
new file mode 100755
index 0000000..e4495ed
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/pacman.conf
@@ -0,0 +1,64 @@
+#
+# /etc/pacman.conf
+#
+# NOTE: If you find a mirror that is geographically close to you, please
+# move it to the top of the server list, so pacman will choose it
+# first.
+#
+# To re-sort your mirror lists by ping/traceroute results, use the
+# /usr/bin/sortmirrors script. It requires the "netselect" package.
+#
+
+# See the pacman manpage for option directives
+
+#
+# GENERAL OPTIONS
+#
+[options]
+LogFile = /var/log/pacman.log
+NoUpgrade = etc/passwd etc/group etc/shadow etc/sudoers
+NoUpgrade = etc/fstab etc/raidtab etc/ld.so.conf
+NoUpgrade = etc/rc.conf etc/rc.local
+NoUpgrade = etc/modprobe.conf etc/modules.conf
+NoUpgrade = etc/lilo.conf boot/grub/menu.lst
+NoUpgrade = data/srv/hobbit/etc/bb-hosts
+NoUpgrade = etc/func/minion.conf
+
+HoldPkg = pacman glibc
+CacheDir = /data/var/cache/pacman/pkg
+#XferCommand = /usr/bin/wget --passive-ftp -c -O %o %u
+
+#
+# REPOSITORIES
+# - can be defined here or included from another file
+# - pacman will search repositories in the order defined here.
+# - local/custom mirrors can be added here or in separate files
+#
+[mv-core-testing]
+Server = http://mvbuild/repo/mv-core-testing/
+
+[mv-extra-testing]
+Server = http://mvbuild/repo/mv-extra-testing/
+
+[svc_pkg]
+Include = /etc/pacman.d/svc_pkg
+
+
+########################ARCH DEFAULTS#############
+#[core]
+# Add your preferred servers here, they will be used first
+#Include = /etc/pacman.d/mirrorlist
+
+#[extra]
+# Add your preferred servers here, they will be used first
+#Include = /etc/pacman.d/mirrorlist
+
+#[community]
+# Add your preferred servers here, they will be used first
+#Include = /etc/pacman.d/mirrorlist
+
+# Unstable is disabled by default. To enable, uncomment the following
+# two lines. You can add preferred servers immediately after the header,
+# and they will be used before the default mirrors.
+#[unstable]
+#Include = /etc/pacman.d/mirrorlist
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/rc.conf b/build_tools/clarch/larch/profiles/MV-local/post_process/rc.conf
new file mode 100755
index 0000000..790269c
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/rc.conf
@@ -0,0 +1,113 @@
+#
+# /etc/rc.conf - Main Configuration for Arch Linux
+#
+
+#
+# -----------------------------------------------------------------------
+# LOCALIZATION
+# -----------------------------------------------------------------------
+#
+# LOCALE: available languages can be listed with the 'locale -a' command
+# HARDWARECLOCK: set to "UTC" or "localtime"
+# TIMEZONE: timezones are found in /usr/share/zoneinfo
+# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
+# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
+# CONSOLEMAP: found in /usr/share/kbd/consoletrans
+# USECOLOR: use ANSI color sequences in startup messages
+#
+LOCALE="en_US.utf8"
+HARDWARECLOCK="UTC"
+TIMEZONE="US/Central"
+KEYMAP="us"
+CONSOLEFONT=
+CONSOLEMAP=
+USECOLOR="no"
+
+#
+# -----------------------------------------------------------------------
+# HARDWARE
+# -----------------------------------------------------------------------
+#
+# Scan hardware and load required modules at bootup
+MOD_AUTOLOAD="yes"
+if [ -f /etc/systemconfig ]
+then
+ . /etc/systemconfig
+fi
+
+if [ x$Audiotype = xOSS -a ! -f /tmp/.alsatest ]
+then
+ ALSABLACKLIST="soundcore"
+else
+ if [ x$Audiotype = x ]
+ then
+ ALSABLACKLIST="soundcore"
+ else
+ ALSABLACKLIST=""
+ fi
+fi
+
+# Module Blacklist - modules in this list will never be loaded by udev
+MOD_BLACKLIST=($ALSABLACKLIST)
+#
+# Modules to load at boot-up (in this order)
+# - prefix a module with a ! to blacklist it
+#
+MODULES=()
+# Scan for LVM volume groups at startup, required if you use LVM
+USELVM="no"
+
+#
+# -----------------------------------------------------------------------
+# NETWORKING
+# -----------------------------------------------------------------------
+#
+HOSTNAME=`cat /etc/hostname`
+
+#The following is only used on the install. After the first boot everything is set from /etc/net.
+
+
+#
+# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available
+# interfaces.
+#
+# Interfaces to start at boot-up (in this order)
+# Declare each interface then list in INTERFACES
+# - prefix an entry in INTERFACES with a ! to disable it
+# - no hyphens in your interface names - Bash doesn't like it
+#
+# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
+#
+lo="lo 127.0.0.1"
+#eth0="dhcp"
+INTERFACES=(lo )
+#
+# Routes to start at boot-up (in this order)
+# Declare each route then list in ROUTES
+# - prefix an entry in ROUTES with a ! to disable it
+#
+gateway="default gw 192.168.0.1"
+ROUTES=(!gateway)
+#
+# Enable these network profiles at boot-up. These are only useful
+# if you happen to need multiple network configurations (ie, laptop users)
+# - set to 'menu' to present a menu during boot-up (dialog package required)
+# - prefix an entry with a ! to disable it
+#
+# Network profiles are found in /etc/network-profiles
+#
+#NET_PROFILES=(main)
+
+#
+# -----------------------------------------------------------------------
+# DAEMONS
+# -----------------------------------------------------------------------
+#
+# Daemons to start at boot-up (in this order)
+# - prefix a daemon with a ! to disable it
+# - prefix a daemon with a @ to start it up in the background
+#
+#DAEMONS=(syslog-ng network netfs crond)
+DAEMONS=(!syslog-ng !hotplug !pcmcia network mysqld dbus avahi-daemon)
+
+# End of file
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/rc.local b/build_tools/clarch/larch/profiles/MV-local/post_process/rc.local
new file mode 100755
index 0000000..0552860
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/rc.local
@@ -0,0 +1,21 @@
+#!/bin/bash
+. /etc/profile
+. ${MV_ROOT}/bin/install_functions.sh
+#install initial database
+pacman -S --noconfirm /data/var/cache/pacman/pkg/mythdb-initial* 2>/dev/null
+
+init_network
+/etc/rc.d/alsa-utils start 0
+init_remote
+random_theme
+
+echo $CMDLINE | grep -q NoX
+if [ $? = 0 ]
+then
+ echo "No auto X option found"
+ /usr/bin/chvt 2
+else
+ /root/startx &
+fi
+
+
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/rc.shutdown b/build_tools/clarch/larch/profiles/MV-local/post_process/rc.shutdown
new file mode 100755
index 0000000..1a8cdbe
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/rc.shutdown
@@ -0,0 +1,104 @@
+#!/bin/bash
+#
+# /etc/rc.shutdown
+#
+
+. /etc/rc.conf
+. /etc/rc.d/functions
+
+# avoid staircase effect
+/bin/stty onlcr
+
+echo " "
+printhl "Initiating Shutdown..."
+echo " "
+
+if [ -x /etc/rc.local.shutdown ]; then
+ /etc/rc.local.shutdown
+fi
+
+if [ "$PREVLEVEL" = "3" -o "$PREVLEVEL" = "5" ]; then
+ # Shutdown daemons
+ let i=${#DAEMONS[@]}
+ while [[ i -ge 0 ]]; do
+ if [[ `echo ${DAEMONS[$i]} | grep '^[^\!]' | wc -l` -eq 1 ]]; then
+ /etc/rc.d/${DAEMONS[$i]#@} stop
+ fi
+ let i=i-1
+ done
+ # find any leftover daemons and shut them down
+ if [ -d /var/run/daemons ]; then
+ for daemon in `ls /var/run/daemons`; do
+ /etc/rc.d/$daemon stop
+ done
+ fi
+fi
+
+# Terminate all processes
+stat_busy "Sending SIGTERM To Processes"
+/sbin/killall5 -15 &> /dev/null
+/bin/sleep 5
+stat_done
+
+stat_busy "Sending SIGKILL To Processes"
+/sbin/killall5 -9 &> /dev/null
+/bin/sleep 1
+stat_done
+
+stat_busy "Saving Random Seed"
+/bin/dd if=/dev/urandom of=/var/run/random-seed count=1 bs=512 2> /dev/null
+stat_done
+
+stat_busy "Saving System Clock"
+if [ "$HARDWARECLOCK" = "UTC" ]; then
+ /sbin/hwclock --directisa --utc --systohc
+else
+ /sbin/hwclock --directisa --localtime --systohc
+fi
+stat_done
+
+# removing psmouse module to fix some reboot issues on newer laptops
+modprobe -r psmouse >/dev/null 2>&1
+
+# Write to wtmp file before unmounting
+/sbin/halt -w
+
+stat_busy "Deactivating Swap"
+/sbin/swapoff -a
+stat_done
+
+stat_busy "Unmounting Filesystems"
+/bin/umount -a
+stat_done
+
+if [ "$USELVM" = "yes" -o "$USELVM" = "YES" ]; then
+ if [ -d /etc/lvm -a -x /sbin/lvm ]; then
+ /bin/mount -n -t sysfs none /sys 2>/dev/null
+ if [ -d /sys/block ]; then
+ stat_busy "Deactivating LVM2 groups"
+ /sbin/lvm vgchange --ignorelockingfailure -a n
+ stat_done
+ umount /sys
+ fi
+ fi
+fi
+
+stat_busy "Remounting Root Filesystem Read-only"
+/bin/mount -n -o remount,ro /
+stat_done
+exit 0
+# Power off or reboot
+if [ "$RUNLEVEL" = "0" ]; then
+ printsep
+ printhl "${C_H2}POWER OFF"
+ /sbin/poweroff -d -f -h -i
+else
+ printsep
+ printhl "${C_H2}REBOOTING"
+ # adding kexec support
+ [ -x /usr/sbin/kexec ] && /usr/sbin/kexec -e > /dev/null 2>&1
+ /sbin/reboot -d -f -i
+fi
+
+# End of file
+# vim: set ts=2 noet:
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/rc.sysinit.patch b/build_tools/clarch/larch/profiles/MV-local/post_process/rc.sysinit.patch
new file mode 100644
index 0000000..69a1ce0
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/rc.sysinit.patch
@@ -0,0 +1,14 @@
+--- rc.sysinit.orig 2008-07-06 19:39:36.000000000 -0500
++++ rc.sysinit 2008-07-06 19:40:28.000000000 -0500
+@@ -9,10 +9,7 @@
+ source_functions
+
+ echo " "
+-printhl "Arch Linux $C_OTHER(${C_H2}Core Dump$C_OTHER)\n"
+-printhl "${C_H2}http://www.archlinux.org"
+-printhl "Copyright 2002-2007 Judd Vinet"
+-printhl "Copyright 2007-2008 Aaron Griffin"
++printhl "MythVantage \n"
+ printhl "Distributed under the GNU General Public License (GPL)"
+ printsep
+
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/root b/build_tools/clarch/larch/profiles/MV-local/post_process/root
new file mode 100644
index 0000000..e6542a2
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/root
@@ -0,0 +1,13 @@
+#
+# DO NOT EDIT THIS FILE MANUALLY!! USE crontab -e INSTEAD.
+#
+
+# <minute> <hour> <day> <month> <dow> <command>
+
+
+01 * * * * /usr/sbin/run-cron /etc/cron.hourly
+*/10 * * * * /usr/sbin/run-cron /etc/cron.tenminutes
+02 00 * * * /usr/sbin/run-cron /etc/cron.daily
+22 00 * * 0 /usr/sbin/run-cron /etc/cron.weekly
+42 00 1 * * /usr/sbin/run-cron /etc/cron.monthly
+
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/securetty b/build_tools/clarch/larch/profiles/MV-local/post_process/securetty
new file mode 100755
index 0000000..68e8a50
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/securetty
@@ -0,0 +1,19 @@
+#
+# /etc/securetty
+#
+
+console
+vc/1
+vc/2
+vc/3
+vc/4
+vc/5
+vc/6
+tty1
+tty2
+tty3
+tty4
+tty5
+tty6
+
+# End of file
diff --git a/build_tools/clarch/larch/profiles/MV-local/post_process/tweak.sh b/build_tools/clarch/larch/profiles/MV-local/post_process/tweak.sh
new file mode 100755
index 0000000..9fa0396
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/post_process/tweak.sh
@@ -0,0 +1,67 @@
+#!/bin/bash
+
+cd /
+#tar -zxvf .tweak/linux-kernel-2.6.16-i486-1.tgz
+#chmod 755 install/doinst.sh
+#install/doinst.sh
+cd .tweak
+#cd /boot
+#ln -s vmlinuz26STB vmlinuz
+#cd -
+#cp fstab /etc/fstab.install
+#cp pacman.conf /etc
+cp menu.lst /boot/grub/menu.lst
+
+cp -f hosts.allow /etc/hosts.allow
+cp -f securetty /etc/securetty
+cp -f rc.conf /etc/rc.conf
+#cp -f rc.local /etc/rc.local
+#cp -f locale.gen /etc/locale.gen
+
+cp -f rc.shutdown /etc/rc.shutdown
+#cp -f inittab /etc/inittab
+
+#cp -f fbsplash-darch-1024x768 /boot/fbsplash-darch-1024x768
+
+
+
+#cp -rf .tilda /data/home/mythtv/.tilda
+ln -s /etc/keylaunchrc /root/.keylaunchrc
+mkdir -p /etc/cron.tenminutes
+cp -f root /var/spool/cron/root
+chmod 0440 /etc/sudoers
+#echo "mvi" > /etc/hostname
+#echo /usr/local/lib >> /etc/ld.so.conf
+#/sbin/ldconfig
+#/usr/sbin/locale-gen
+
+chmod 777 /tmp
+mkdir -p /data/home/mythtv/.mythtv
+ln -s /etc/lircrc /data/home/mythtv/.mythtv/lircrc
+ln -s /etc/lircrc /data/home/mythtv/.lircrc
+cp -f /etc/skel/.bashrc /data/home/mythtv/
+cp -f /etc/skel/.bash_profile /data/home/mythtv/
+cp -f /etc/skel/.bashrc /root/
+cp -f /etc/skel/.bash_profile /root/
+mkdir -p /data/home/mythtv/templates
+chown -R mythtv /data/media
+chown -R mythtv /data/home/mythtv
+ln -s /usr/sbin/chroot /usr/bin/chroot
+ln -s /bin/lsmod /sbin/lsmod
+/sbin/add_service.sh netfs
+/sbin/add_service.sh oss
+/sbin/add_service.sh syslog-ng
+/sbin/remove_service.sh alsa-utils
+/usr/bin/chage -d 01-01-2000 nobody
+/usr/bin/chage -E 01-01-3000 nobody
+cp /etc/pam.d/chage /etc/pam.d/chsh
+chsh -s /bin/bash nobody
+
+
+cd /etc/rc.d
+echo "patching functions"
+patch -p0 </.tweak/functions.patch
+cd /etc
+echo "patching rc.sysinit"
+patch -p0 </.tweak/rc.sysinit.patch
+ln -s /bin/bash /bin/ash
diff --git a/build_tools/clarch/larch/profiles/MV-local/rcconfx b/build_tools/clarch/larch/profiles/MV-local/rcconfx
new file mode 100644
index 0000000..80e7dfa
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/rcconfx
@@ -0,0 +1,16 @@
+#
+# patch file for /etc/rc.conf
+#
+LOCALE="en_US.utf8"
+HARDWARECLOCK="UTC"
+TIMEZONE="UTC"
+ddKEYMAP="de-latin1-nodeadkeys"
+MODULES=()
+
+HOSTNAME="mvi"
+
+USELVM="no"
+
+#eth0="dhcp"
+
+#DAEMONS=(syslog-ng mysqld)
diff --git a/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/conf.d/dhcpcd b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/conf.d/dhcpcd
new file mode 100644
index 0000000..ab53c30
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/conf.d/dhcpcd
@@ -0,0 +1,6 @@
+#
+# Arguments to be passed to the DHCP client daemon
+#
+
+DHCPCD_ARGS="-t 10 -h $HOSTNAME"
+
diff --git a/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/hosts.allow b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/hosts.allow
new file mode 100644
index 0000000..ca19dbb
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/hosts.allow
@@ -0,0 +1,7 @@
+#
+# /etc/hosts.allow
+#
+ALL: 192.168.
+ALL: 10.
+ALL: 127.0.0.1
+# End of file
diff --git a/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/inittab b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/inittab
new file mode 100644
index 0000000..b8b2b3a
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/inittab
@@ -0,0 +1,42 @@
+#
+# /etc/inittab
+#
+
+# Runlevels:
+# 0 Halt
+# 1(S) Single-user
+# 2 Not used
+# 3 Multi-user
+# 4 Not used
+# 5 X11
+# 6 Reboot
+
+## Only one of the following two lines can be uncommented!
+# Boot to console
+id:3:initdefault:
+# Boot to X11
+#id:5:initdefault:
+
+rc::sysinit:/etc/rc.sysinit
+rs:S1:wait:/etc/rc.single
+rm:2345:wait:/etc/rc.multi
+rh:06:wait:/etc/rc.shutdown
+su:S:wait:/sbin/sulogin -p
+
+# -8 options fixes umlauts problem on login
+c1:2345:respawn:/sbin/agetty -8 38400 vc/1 linux -n -l /etc/loginroot
+c2:2345:respawn:/sbin/agetty -8 38400 vc/2 linux
+c3:2345:respawn:/sbin/agetty -8 38400 vc/3 linux
+c4:2345:respawn:/sbin/agetty -8 38400 vc/4 linux
+c5:2345:respawn:/sbin/agetty -8 38400 vc/5 linux
+c6:2345:respawn:/sbin/agetty -8 38400 vc/6 linux
+
+ca::ctrlaltdel:/sbin/shutdown -t3 -r now
+
+# Example lines for starting a login manager
+x:5:respawn:/usr/bin/xdm -nodaemon
+#x:5:respawn:/usr/sbin/gdm -nodaemon
+#x:5:respawn:/opt/kde/bin/kdm -nodaemon
+#x:5:respawn:/usr/bin/slim >& /dev/null
+
+# End of file
diff --git a/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/larch-shutdown b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/larch-shutdown
new file mode 100644
index 0000000..d614d4b
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/larch-shutdown
@@ -0,0 +1,47 @@
+# Functions used by rc.shutdown
+# Modified versions for larch live systems
+
+f_saveclock ()
+{
+ :
+}
+
+f_swapoff ()
+{
+ ############################# Include session saving functions
+ # . /opt/larch-live/session-save/shutdown2
+ # if [ -f /tmp/checkse ]; then
+ # . /tmp/checkse
+ #else
+ # checkse
+ # fi
+
+ if [ -n "${saving}" ] && ! session_save; then
+ echo
+ echo "If you know what you are doing, you may be able to recover"
+ echo "something from this unpleasant situation."
+ echo
+ echo "You may use the command line to investigate further ..."
+ echo
+ echo "When finished please enter 'exit', the shutdown process will"
+ echo "then continue."
+ sh -i
+ fi
+
+ #############################
+
+ stat_busy "Deactivating Swap"
+ /sbin/swapoff -a
+ stat_done
+}
+
+f_remountro ()
+{
+ if [ -n "${ejectdev}" ]; then
+ echo "Ejecting live CD"
+ eject ${ejectdev}
+ echo "sleeping for 6 seconds"
+ sleep 6
+
+ fi
+}
diff --git a/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/ppp/options b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/ppp/options
new file mode 100644
index 0000000..237c390
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/ppp/options
@@ -0,0 +1,352 @@
+# /etc/ppp/options
+#
+# Originally created by Jim Knoble <jmknoble@mercury.interpath.net>
+# Modified for Debian by alvar Bray <alvar@meiko.co.uk>
+# Modified for PPP Server setup by Christoph Lameter <clameter@debian.org>
+# Modified for ArchLinux by Manolis Tzanidakis <manolis@archlinux.org>
+#
+# To quickly see what options are active in this file, use this command:
+# egrep -v '#|^ *$' /etc/ppp/options
+
+# Specify which DNS Servers the incoming Win95 or WinNT Connection should use
+# Two Servers can be remotely configured
+# ms-dns 192.168.1.1
+# ms-dns 192.168.1.2
+
+# Specify which WINS Servers the incoming connection Win95 or WinNT should use
+# ms-wins 192.168.1.50
+# ms-wins 192.168.1.51
+
+# Run the executable or shell command specified after pppd has
+# terminated the link. This script could, for example, issue commands
+# to the modem to cause it to hang up if hardware modem control signals
+# were not available.
+#disconnect "chat -- \d+++\d\c OK ath0 OK"
+
+# async character map -- 32-bit hex; each bit is a character
+# that needs to be escaped for pppd to receive it. 0x00000001
+# represents '\x01', and 0x80000000 represents '\x1f'.
+asyncmap 0
+
+# Require the peer to authenticate itself before allowing network
+# packets to be sent or received.
+# Please do not disable this setting. It is expected to be standard in
+# future releases of pppd. Use the call option (see manpage) to disable
+# authentication for specific peers.
+#auth
+
+# Use hardware flow control (i.e. RTS/CTS) to control the flow of data
+# on the serial port.
+crtscts
+
+# Use software flow control (i.e. XON/XOFF) to control the flow of data
+# on the serial port.
+#xonxoff
+
+# Specifies that certain characters should be escaped on transmission
+# (regardless of whether the peer requests them to be escaped with its
+# async control character map). The characters to be escaped are
+# specified as a list of hex numbers separated by commas. Note that
+# almost any character can be specified for the escape option, unlike
+# the asyncmap option which only allows control characters to be
+# specified. The characters which may not be escaped are those with hex
+# values 0x20 - 0x3f or 0x5e.
+#escape 11,13,ff
+
+# Don't use the modem control lines.
+#local
+
+# Specifies that pppd should use a UUCP-style lock on the serial device
+# to ensure exclusive access to the device.
+lock
+
+# Don't show the passwords when logging the contents of PAP packets.
+# This is the default.
+hide-password
+
+# When logging the contents of PAP packets, this option causes pppd to
+# show the password string in the log message.
+#show-password
+
+# Use the modem control lines. On Ultrix, this option implies hardware
+# flow control, as for the crtscts option. (This option is not fully
+# implemented.)
+modem
+
+# Set the MRU [Maximum Receive Unit] value to <n> for negotiation. pppd
+# will ask the peer to send packets of no more than <n> bytes. The
+# minimum MRU value is 128. The default MRU value is 1500. A value of
+# 296 is recommended for slow links (40 bytes for TCP/IP header + 256
+# bytes of data).
+#mru 542
+
+# Set the interface netmask to <n>, a 32 bit netmask in "decimal dot"
+# notation (e.g. 255.255.255.0).
+#netmask 255.255.255.0
+
+# Disables the default behaviour when no local IP address is specified,
+# which is to determine (if possible) the local IP address from the
+# hostname. With this option, the peer will have to supply the local IP
+# address during IPCP negotiation (unless it specified explicitly on the
+# command line or in an options file).
+#noipdefault
+
+# Enables the "passive" option in the LCP. With this option, pppd will
+# attempt to initiate a connection; if no reply is received from the
+# peer, pppd will then just wait passively for a valid LCP packet from
+# the peer (instead of exiting, as it does without this option).
+#passive
+
+# With this option, pppd will not transmit LCP packets to initiate a
+# connection until a valid LCP packet is received from the peer (as for
+# the "passive" option with old versions of pppd).
+#silent
+
+# Don't request or allow negotiation of any options for LCP and IPCP
+# (use default values).
+#-all
+
+# Disable Address/Control compression negotiation (use default, i.e.
+# address/control field disabled).
+#-ac
+
+# Disable asyncmap negotiation (use the default asyncmap, i.e. escape
+# all control characters).
+#-am
+
+# Don't fork to become a background process (otherwise pppd will do so
+# if a serial device is specified).
+#-detach
+
+# Disable IP address negotiation (with this option, the remote IP
+# address must be specified with an option on the command line or in
+# an options file).
+#-ip
+
+# Disable IPCP negotiation and IP communication. This option should
+# only be required if the peer is buggy and gets confused by requests
+# from pppd for IPCP negotiation.
+#noip
+
+# Disable magic number negotiation. With this option, pppd cannot
+# detect a looped-back line.
+#-mn
+
+# Disable MRU [Maximum Receive Unit] negotiation (use default, i.e.
+# 1500).
+#-mru
+
+# Disable protocol field compression negotiation (use default, i.e.
+# protocol field compression disabled).
+#-pc
+
+# Require the peer to authenticate itself using PAP.
+#+pap
+
+# Don't agree to authenticate using PAP.
+#-pap
+
+# Require the peer to authenticate itself using CHAP [Cryptographic
+# Handshake Authentication Protocol] authentication.
+#+chap
+
+# Don't agree to authenticate using CHAP.
+#-chap
+
+# Disable negotiation of Van Jacobson style IP header compression (use
+# default, i.e. no compression).
+#-vj
+
+# Increase debugging level (same as -d). If this option is given, pppd
+# will log the contents of all control packets sent or received in a
+# readable form. The packets are logged through syslog with facility
+# daemon and level debug. This information can be directed to a file by
+# setting up /etc/syslog.conf appropriately (see syslog.conf(5)). (If
+# pppd is compiled with extra debugging enabled, it will log messages
+# using facility local2 instead of daemon).
+#debug
+
+# Append the domain name <d> to the local host name for authentication
+# purposes. For example, if gethostname() returns the name porsche,
+# but the fully qualified domain name is porsche.Quotron.COM, you would
+# use the domain option to set the domain name to Quotron.COM.
+#domain <d>
+
+# Enable debugging code in the kernel-level PPP driver. The argument n
+# is a number which is the sum of the following values: 1 to enable
+# general debug messages, 2 to request that the contents of received
+# packets be printed, and 4 to request that the contents of transmitted
+# packets be printed.
+#kdebug n
+
+# Set the MTU [Maximum Transmit Unit] value to <n>. Unless the peer
+# requests a smaller value via MRU negotiation, pppd will request that
+# the kernel networking code send data packets of no more than n bytes
+# through the PPP network interface.
+#mtu <n>
+
+# Set the name of the local system for authentication purposes to <n>.
+# This is a privileged option. With this option, pppd will use lines in the
+# secrets files which have <n> as the second field when looking for a
+# secret to use in authenticating the peer. In addition, unless overridden
+# with the user option, <n> will be used as the name to send to the peer
+# when authenticating the local system to the peer. (Note that pppd does
+# not append the domain name to <n>.)
+#name <n>
+
+# Enforce the use of the hostname as the name of the local system for
+# authentication purposes (overrides the name option).
+#usehostname
+
+# Set the assumed name of the remote system for authentication purposes
+# to <n>.
+#remotename <n>
+
+# Add an entry to this system's ARP [Address Resolution Protocol]
+# table with the IP address of the peer and the Ethernet address of this
+# system.
+proxyarp
+
+# Use the system password database for authenticating the peer using
+# PAP. Note: mgetty already provides this option. If this is specified
+# then dialin from users using a script under Linux to fire up ppp wont work.
+# login
+
+# If this option is given, pppd will send an LCP echo-request frame to the
+# peer every n seconds. Normally the peer should respond to the echo-request
+# by sending an echo-reply. This option can be used with the
+# lcp-echo-failure option to detect that the peer is no longer connected.
+lcp-echo-interval 30
+
+# If this option is given, pppd will presume the peer to be dead if n
+# LCP echo-requests are sent without receiving a valid LCP echo-reply.
+# If this happens, pppd will terminate the connection. Use of this
+# option requires a non-zero value for the lcp-echo-interval parameter.
+# This option can be used to enable pppd to terminate after the physical
+# connection has been broken (e.g., the modem has hung up) in
+# situations where no hardware modem control lines are available.
+lcp-echo-failure 4
+
+# Set the LCP restart interval (retransmission timeout) to <n> seconds
+# (default 3).
+#lcp-restart <n>
+
+# Set the maximum number of LCP terminate-request transmissions to <n>
+# (default 3).
+#lcp-max-terminate <n>
+
+# Set the maximum number of LCP configure-request transmissions to <n>
+# (default 10).
+#lcp-max-configure <n>
+
+# Set the maximum number of LCP configure-NAKs returned before starting
+# to send configure-Rejects instead to <n> (default 10).
+#lcp-max-failure <n>
+
+# Set the IPCP restart interval (retransmission timeout) to <n>
+# seconds (default 3).
+#ipcp-restart <n>
+
+# Set the maximum number of IPCP terminate-request transmissions to <n>
+# (default 3).
+#ipcp-max-terminate <n>
+
+# Set the maximum number of IPCP configure-request transmissions to <n>
+# (default 10).
+#ipcp-max-configure <n>
+
+# Set the maximum number of IPCP configure-NAKs returned before starting
+# to send configure-Rejects instead to <n> (default 10).
+#ipcp-max-failure <n>
+
+# Set the PAP restart interval (retransmission timeout) to <n> seconds
+# (default 3).
+#pap-restart <n>
+
+# Set the maximum number of PAP authenticate-request transmissions to
+# <n> (default 10).
+#pap-max-authreq <n>
+
+# Set the maximum time that pppd will wait for the peer to authenticate
+# itself with PAP to <n> seconds (0 means no limit).
+#pap-timeout <n>
+
+# Set the CHAP restart interval (retransmission timeout for
+# challenges) to <n> seconds (default 3).
+#chap-restart <n>
+
+# Set the maximum number of CHAP challenge transmissions to <n>
+# (default 10).
+#chap-max-challenge
+
+# If this option is given, pppd will rechallenge the peer every <n>
+# seconds.
+#chap-interval <n>
+
+# With this option, pppd will accept the peer's idea of our local IP
+# address, even if the local IP address was specified in an option.
+#ipcp-accept-local
+
+# With this option, pppd will accept the peer's idea of its (remote) IP
+# address, even if the remote IP address was specified in an option.
+#ipcp-accept-remote
+
+# Disable the IPXCP and IPX protocols.
+# To let pppd pass IPX packets comment this out --- you'll probably also
+# want to install ipxripd, and have the Internal IPX Network option enabled
+# in your kernel. /usr/doc/HOWTO/IPX-HOWTO.gz contains more info.
+noipx
+
+# Exit once a connection has been made and terminated. This is the default,
+# unless the `persist' or `demand' option has been specified.
+#nopersist
+
+# Do not exit after a connection is terminated; instead try to reopen
+# the connection.
+#persist
+
+# Terminate after n consecutive failed connection attempts.
+# A value of 0 means no limit. The default value is 10.
+#maxfail <n>
+
+# Initiate the link only on demand, i.e. when data traffic is present.
+# With this option, the remote IP address must be specified by the user on
+# the command line or in an options file. Pppd will initially configure
+# the interface and enable it for IP traffic without connecting to the peer.
+# When traffic is available, pppd will connect to the peer and perform
+# negotiation, authentication, etc. When this is completed, pppd will
+# commence passing data packets (i.e., IP packets) across the link.
+#demand
+
+# Specifies that pppd should disconnect if the link is idle for <n> seconds.
+# The link is idle when no data packets (i.e. IP packets) are being sent or
+# received. Note: it is not advisable to use this option with the persist
+# option without the demand option. If the active-filter option is given,
+# data packets which are rejected by the specified activity filter also
+# count as the link being idle.
+#idle <n>
+
+# Specifies how many seconds to wait before re-initiating the link after
+# it terminates. This option only has any effect if the persist or demand
+# option is used. The holdoff period is not applied if the link was
+# terminated because it was idle.
+#holdoff <n>
+
+# Wait for up n milliseconds after the connect script finishes for a valid
+# PPP packet from the peer. At the end of this time, or when a valid PPP
+# packet is received from the peer, pppd will commence negotiation by
+# sending its first LCP packet. The default value is 1000 (1 second).
+# This wait period only applies if the connect or pty option is used.
+#connect-delay <n>
+
+# Packet filtering: for more information, see pppd(8)
+# Any packets matching the filter expression will be interpreted as link
+# activity, and will cause a "demand" connection to be activated, and reset
+# the idle connection timer. (idle option)
+# The filter expression is akin to that of tcpdump(1)
+#active-filter <filter-expression>
+
+# uncomment the line below this if you use PPPoE
+#plugin /usr/lib/pppd/plugins/pppoe.so
+
+# ---<End of File>---
diff --git a/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/rc.local b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/rc.local
new file mode 100755
index 0000000..c1b0154
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/etc/rc.local
@@ -0,0 +1,21 @@
+#!/bin/bash
+. /etc/profile
+. ${MV_ROOT}/bin/install_functions.sh
+#install initial database
+pacman -S --noconfirm mythdb-initial 2>/dev/null
+
+init_network
+/etc/rc.d/alsa-utils start 0
+init_remote
+random_theme
+
+echo $CMDLINE | grep -q NoX
+if [ $? = 0 ]
+then
+ echo "No auto X option found"
+ /usr/bin/chvt 2
+else
+ /root/startx &
+fi
+
+
diff --git a/build_tools/clarch/larch/profiles/MV-local/rootoverlay/root/.bashrc b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/root/.bashrc
new file mode 100644
index 0000000..3e5c29c
--- /dev/null
+++ b/build_tools/clarch/larch/profiles/MV-local/rootoverlay/root/.bashrc
@@ -0,0 +1,2 @@
+alias ls='ls --color=auto'
+PS1='[\u@\h \W]\$ '