diff options
Diffstat (limited to 'abs/core-testing/ppp/options')
| -rw-r--r-- | abs/core-testing/ppp/options | 352 |
1 files changed, 0 insertions, 352 deletions
diff --git a/abs/core-testing/ppp/options b/abs/core-testing/ppp/options deleted file mode 100644 index 6369184..0000000 --- a/abs/core-testing/ppp/options +++ /dev/null @@ -1,352 +0,0 @@ -# /etc/ppp/options -# -# Originally created by Jim Knoble <jmknoble@mercury.interpath.net> -# Modified for Debian by alvar Bray <alvar@meiko.co.uk> -# Modified for PPP Server setup by Christoph Lameter <clameter@debian.org> -# Modified for ArchLinux by Manolis Tzanidakis <manolis@archlinux.org> -# -# To quickly see what options are active in this file, use this command: -# egrep -v '#|^ *$' /etc/ppp/options - -# Specify which DNS Servers the incoming Win95 or WinNT Connection should use -# Two Servers can be remotely configured -# ms-dns 192.168.1.1 -# ms-dns 192.168.1.2 - -# Specify which WINS Servers the incoming connection Win95 or WinNT should use -# ms-wins 192.168.1.50 -# ms-wins 192.168.1.51 - -# Run the executable or shell command specified after pppd has -# terminated the link. This script could, for example, issue commands -# to the modem to cause it to hang up if hardware modem control signals -# were not available. -#disconnect "chat -- \d+++\d\c OK ath0 OK" - -# async character map -- 32-bit hex; each bit is a character -# that needs to be escaped for pppd to receive it. 0x00000001 -# represents '\x01', and 0x80000000 represents '\x1f'. -asyncmap 0 - -# Require the peer to authenticate itself before allowing network -# packets to be sent or received. -# Please do not disable this setting. It is expected to be standard in -# future releases of pppd. Use the call option (see manpage) to disable -# authentication for specific peers. -auth - -# Use hardware flow control (i.e. RTS/CTS) to control the flow of data -# on the serial port. -crtscts - -# Use software flow control (i.e. XON/XOFF) to control the flow of data -# on the serial port. -#xonxoff - -# Specifies that certain characters should be escaped on transmission -# (regardless of whether the peer requests them to be escaped with its -# async control character map). The characters to be escaped are -# specified as a list of hex numbers separated by commas. Note that -# almost any character can be specified for the escape option, unlike -# the asyncmap option which only allows control characters to be -# specified. The characters which may not be escaped are those with hex -# values 0x20 - 0x3f or 0x5e. -#escape 11,13,ff - -# Don't use the modem control lines. -#local - -# Specifies that pppd should use a UUCP-style lock on the serial device -# to ensure exclusive access to the device. -lock - -# Don't show the passwords when logging the contents of PAP packets. -# This is the default. -hide-password - -# When logging the contents of PAP packets, this option causes pppd to -# show the password string in the log message. -#show-password - -# Use the modem control lines. On Ultrix, this option implies hardware -# flow control, as for the crtscts option. (This option is not fully -# implemented.) -modem - -# Set the MRU [Maximum Receive Unit] value to <n> for negotiation. pppd -# will ask the peer to send packets of no more than <n> bytes. The -# minimum MRU value is 128. The default MRU value is 1500. A value of -# 296 is recommended for slow links (40 bytes for TCP/IP header + 256 -# bytes of data). -#mru 542 - -# Set the interface netmask to <n>, a 32 bit netmask in "decimal dot" -# notation (e.g. 255.255.255.0). -#netmask 255.255.255.0 - -# Disables the default behaviour when no local IP address is specified, -# which is to determine (if possible) the local IP address from the -# hostname. With this option, the peer will have to supply the local IP -# address during IPCP negotiation (unless it specified explicitly on the -# command line or in an options file). -#noipdefault - -# Enables the "passive" option in the LCP. With this option, pppd will -# attempt to initiate a connection; if no reply is received from the -# peer, pppd will then just wait passively for a valid LCP packet from -# the peer (instead of exiting, as it does without this option). -#passive - -# With this option, pppd will not transmit LCP packets to initiate a -# connection until a valid LCP packet is received from the peer (as for -# the "passive" option with old versions of pppd). -#silent - -# Don't request or allow negotiation of any options for LCP and IPCP -# (use default values). -#-all - -# Disable Address/Control compression negotiation (use default, i.e. -# address/control field disabled). -#-ac - -# Disable asyncmap negotiation (use the default asyncmap, i.e. escape -# all control characters). -#-am - -# Don't fork to become a background process (otherwise pppd will do so -# if a serial device is specified). -#-detach - -# Disable IP address negotiation (with this option, the remote IP -# address must be specified with an option on the command line or in -# an options file). -#-ip - -# Disable IPCP negotiation and IP communication. This option should -# only be required if the peer is buggy and gets confused by requests -# from pppd for IPCP negotiation. -#noip - -# Disable magic number negotiation. With this option, pppd cannot -# detect a looped-back line. -#-mn - -# Disable MRU [Maximum Receive Unit] negotiation (use default, i.e. -# 1500). -#-mru - -# Disable protocol field compression negotiation (use default, i.e. -# protocol field compression disabled). -#-pc - -# Require the peer to authenticate itself using PAP. -#+pap - -# Don't agree to authenticate using PAP. -#-pap - -# Require the peer to authenticate itself using CHAP [Cryptographic -# Handshake Authentication Protocol] authentication. -#+chap - -# Don't agree to authenticate using CHAP. -#-chap - -# Disable negotiation of Van Jacobson style IP header compression (use -# default, i.e. no compression). -#-vj - -# Increase debugging level (same as -d). If this option is given, pppd -# will log the contents of all control packets sent or received in a -# readable form. The packets are logged through syslog with facility -# daemon and level debug. This information can be directed to a file by -# setting up /etc/syslog.conf appropriately (see syslog.conf(5)). (If -# pppd is compiled with extra debugging enabled, it will log messages -# using facility local2 instead of daemon). -#debug - -# Append the domain name <d> to the local host name for authentication -# purposes. For example, if gethostname() returns the name porsche, -# but the fully qualified domain name is porsche.Quotron.COM, you would -# use the domain option to set the domain name to Quotron.COM. -#domain <d> - -# Enable debugging code in the kernel-level PPP driver. The argument n -# is a number which is the sum of the following values: 1 to enable -# general debug messages, 2 to request that the contents of received -# packets be printed, and 4 to request that the contents of transmitted -# packets be printed. -#kdebug n - -# Set the MTU [Maximum Transmit Unit] value to <n>. Unless the peer -# requests a smaller value via MRU negotiation, pppd will request that -# the kernel networking code send data packets of no more than n bytes -# through the PPP network interface. -#mtu <n> - -# Set the name of the local system for authentication purposes to <n>. -# This is a privileged option. With this option, pppd will use lines in the -# secrets files which have <n> as the second field when looking for a -# secret to use in authenticating the peer. In addition, unless overridden -# with the user option, <n> will be used as the name to send to the peer -# when authenticating the local system to the peer. (Note that pppd does -# not append the domain name to <n>.) -#name <n> - -# Enforce the use of the hostname as the name of the local system for -# authentication purposes (overrides the name option). -#usehostname - -# Set the assumed name of the remote system for authentication purposes -# to <n>. -#remotename <n> - -# Add an entry to this system's ARP [Address Resolution Protocol] -# table with the IP address of the peer and the Ethernet address of this -# system. -proxyarp - -# Use the system password database for authenticating the peer using -# PAP. Note: mgetty already provides this option. If this is specified -# then dialin from users using a script under Linux to fire up ppp wont work. -# login - -# If this option is given, pppd will send an LCP echo-request frame to the -# peer every n seconds. Normally the peer should respond to the echo-request -# by sending an echo-reply. This option can be used with the -# lcp-echo-failure option to detect that the peer is no longer connected. -lcp-echo-interval 30 - -# If this option is given, pppd will presume the peer to be dead if n -# LCP echo-requests are sent without receiving a valid LCP echo-reply. -# If this happens, pppd will terminate the connection. Use of this -# option requires a non-zero value for the lcp-echo-interval parameter. -# This option can be used to enable pppd to terminate after the physical -# connection has been broken (e.g., the modem has hung up) in -# situations where no hardware modem control lines are available. -lcp-echo-failure 4 - -# Set the LCP restart interval (retransmission timeout) to <n> seconds -# (default 3). -#lcp-restart <n> - -# Set the maximum number of LCP terminate-request transmissions to <n> -# (default 3). -#lcp-max-terminate <n> - -# Set the maximum number of LCP configure-request transmissions to <n> -# (default 10). -#lcp-max-configure <n> - -# Set the maximum number of LCP configure-NAKs returned before starting -# to send configure-Rejects instead to <n> (default 10). -#lcp-max-failure <n> - -# Set the IPCP restart interval (retransmission timeout) to <n> -# seconds (default 3). -#ipcp-restart <n> - -# Set the maximum number of IPCP terminate-request transmissions to <n> -# (default 3). -#ipcp-max-terminate <n> - -# Set the maximum number of IPCP configure-request transmissions to <n> -# (default 10). -#ipcp-max-configure <n> - -# Set the maximum number of IPCP configure-NAKs returned before starting -# to send configure-Rejects instead to <n> (default 10). -#ipcp-max-failure <n> - -# Set the PAP restart interval (retransmission timeout) to <n> seconds -# (default 3). -#pap-restart <n> - -# Set the maximum number of PAP authenticate-request transmissions to -# <n> (default 10). -#pap-max-authreq <n> - -# Set the maximum time that pppd will wait for the peer to authenticate -# itself with PAP to <n> seconds (0 means no limit). -#pap-timeout <n> - -# Set the CHAP restart interval (retransmission timeout for -# challenges) to <n> seconds (default 3). -#chap-restart <n> - -# Set the maximum number of CHAP challenge transmissions to <n> -# (default 10). -#chap-max-challenge - -# If this option is given, pppd will rechallenge the peer every <n> -# seconds. -#chap-interval <n> - -# With this option, pppd will accept the peer's idea of our local IP -# address, even if the local IP address was specified in an option. -#ipcp-accept-local - -# With this option, pppd will accept the peer's idea of its (remote) IP -# address, even if the remote IP address was specified in an option. -#ipcp-accept-remote - -# Disable the IPXCP and IPX protocols. -# To let pppd pass IPX packets comment this out --- you'll probably also -# want to install ipxripd, and have the Internal IPX Network option enabled -# in your kernel. /usr/doc/HOWTO/IPX-HOWTO.gz contains more info. -noipx - -# Exit once a connection has been made and terminated. This is the default, -# unless the `persist' or `demand' option has been specified. -#nopersist - -# Do not exit after a connection is terminated; instead try to reopen -# the connection. -#persist - -# Terminate after n consecutive failed connection attempts. -# A value of 0 means no limit. The default value is 10. -#maxfail <n> - -# Initiate the link only on demand, i.e. when data traffic is present. -# With this option, the remote IP address must be specified by the user on -# the command line or in an options file. Pppd will initially configure -# the interface and enable it for IP traffic without connecting to the peer. -# When traffic is available, pppd will connect to the peer and perform -# negotiation, authentication, etc. When this is completed, pppd will -# commence passing data packets (i.e., IP packets) across the link. -#demand - -# Specifies that pppd should disconnect if the link is idle for <n> seconds. -# The link is idle when no data packets (i.e. IP packets) are being sent or -# received. Note: it is not advisable to use this option with the persist -# option without the demand option. If the active-filter option is given, -# data packets which are rejected by the specified activity filter also -# count as the link being idle. -#idle <n> - -# Specifies how many seconds to wait before re-initiating the link after -# it terminates. This option only has any effect if the persist or demand -# option is used. The holdoff period is not applied if the link was -# terminated because it was idle. -#holdoff <n> - -# Wait for up n milliseconds after the connect script finishes for a valid -# PPP packet from the peer. At the end of this time, or when a valid PPP -# packet is received from the peer, pppd will commence negotiation by -# sending its first LCP packet. The default value is 1000 (1 second). -# This wait period only applies if the connect or pty option is used. -#connect-delay <n> - -# Packet filtering: for more information, see pppd(8) -# Any packets matching the filter expression will be interpreted as link -# activity, and will cause a "demand" connection to be activated, and reset -# the idle connection timer. (idle option) -# The filter expression is akin to that of tcpdump(1) -#active-filter <filter-expression> - -# uncomment the line below this if you use PPPoE -#plugin /usr/lib/pppd/plugins/pppoe.so - -# ---<End of File>--- |