diff options
Diffstat (limited to 'abs/core-testing/udev/readme-udev-arch.txt')
| -rw-r--r-- | abs/core-testing/udev/readme-udev-arch.txt | 266 |
1 files changed, 0 insertions, 266 deletions
diff --git a/abs/core-testing/udev/readme-udev-arch.txt b/abs/core-testing/udev/readme-udev-arch.txt deleted file mode 100644 index e903a6b..0000000 --- a/abs/core-testing/udev/readme-udev-arch.txt +++ /dev/null @@ -1,266 +0,0 @@ -========================== -Cold/Hotplugging with Udev -========================== -Version 1.1.6 -written by Tobias Powalowski <tpowa@archlinux.org> - ---------------- -* Requirements: ---------------- -- recommended kernel >=2.6.18 for this udev to work properly. -- No more DevFS device paths! If you have them, update /etc/fstab: - /dev/discs/... etc. has been deprecated in favor of the old style: - /dev/discs/disc0/part1 -> /dev/hda1 - /dev/discs/disc1/part2 -> /dev/hdb2 -- /etc/modprobe.conf should be cleaned from old install entries (see below). - ---------------- -* Udev Changes: ---------------- -- The syntax of udev rules has been changed in >=098 release, please update your rules. - --- Snip Changelog Udev 098 - Renaming of some key names: - BUS -> SUBSYSTEMS - ID -> KERNELS - SYSFS -> ATTRS - DRIVER -> DRIVERS - ATTR{file}="value" can be used now, to write to a sysfs file of the - event device. Instead of: - ..., SYSFS{type}=="0|7|14", RUN+="/bin/sh -c 'echo 60 > /sys$$DEVPATH/timeout'" - we now can do: - ..., ATTR{type}=="0|7|14", ATTR{timeout}="60" - All the PHYSDEV* keys are deprecated and will be removed from a - future kernel: - PHYDEVPATH - is the path of a parent device and should not be - needed at all. - PHYSDEVBUS - is just a SUBSYSTEM value of a parent, and can be - matched with SUBSYSTEMS== - PHYSDEVDRIVER - for bus devices it is available as ENV{DRIVER}. - Newer kernels will have DRIVER in the environment, - for older kernels udev puts in. Class device will - no longer carry this property of a parent and - DRIVERS== can be used to match such a parent value. - Note that ENV{DRIVER} is only available for a few bus devices, where - the driver is already bound at device event time. On coldplug, the - events for a lot devices are already bound to a driver, and they will have - that value set. But on hotplug, at the time the kernel creates the device, - it can't know what driver may claim the device after that, therefore - in most cases it will be empty. - --- snap Changelog Udev 098 -- optional udev >= 099 Persistent rules generator for network and cd/dvd devices was added. -- default udev rules are installed to /lib/udev/rules.d/, they can be overriden by placing - own rules files to /etc/udev/rules.d/ . - ---------------- -* How it works: ---------------- -- Udev replaces the functionality of hotplug and hwdetect scripts. -- Udev does autoloading of modules and coldplugging. -- Udev loads the modules simultaneously, which is much faster, - but can cause some troubles with multiple network/sound/etc devices - (see below). -- To reload your rules please use '/sbin/udevadm trigger'. - -====================== -* Autoloading modules: -====================== - -------------------------------------------------------------------------- -* Module autoloading is controlled by MOD_AUTOLOAD="" in /etc/rc.conf -------------------------------------------------------------------------- -MOD_AUTOLOAD="yes" in /etc/rc.conf is necessary: -- if you want module autodetection -- if you want modules be loaded by udev (hotplugging and coldplugging) - -MOD_AUTOLOAD="no" is necessary: -- if you want to load modules strictly using 'modprobe <module>' -- if you want to load only the modules listed in the MODULES=() array - in /etc/rc.conf - ---------------- -* Blacklisting: ---------------- -- means udev will never try to load the module, even if MOD_AUTOLOAD="yes" - is set. - -You can do this in 2 ways: -- MOD_BLACKLIST=(moduleA moduleB) -- MODULES=(!moduleA !moduleB) - -Both entries mean the same thing to udev. MOD_BLACKLIST was used by hwdetect. -hwdetect does not understand the MODULES= syntax, but it doesn't have to -- it -is only used in mkinitrd now. - -================================== -* Boot parameter: load_modules=off -================================== - -- No modules are loaded during boot using udev autoloading or the MODULES array -- Useful for repairing your system if something goes wrong during udev startup - and/or during loading modules - -================================== -* Boot parameter: disablemodules= -================================== - -- list modules there that shouldn't be loaded by udev -- Syntax: disablemodules=module1,module2,module3,... -- Useful for repairing your system if something goes wrong during udev startup - and/or during loading modules and you know the module that causes the trouble. - -======================================== -* Persistent CD/DVD symlinks (optional): -======================================== - -- To enable this feature copy in /etc/udev/rules.d - 75-cd-aliases-generator.rules.optinal - to 75-cd-aliases-generator.rules - Also disable this part in /lib/udev/rules.d/81-arch.rules by putting a # in front: - --- snip - ACTION=="add", SUBSYSTEMS=="ide", KERNEL=="hd[a-z]", ATTR{removable}=="1", ATTRS{media}=="cdrom*", RUN+="/lib/udev/cdsymlinks.sh" - ACTION=="add", SUBSYSTEMS=="scsi", KERNEL=="sr[0-9]*", ATTRS{type}=="5", RUN+="/lib/udev/cdsymlinks.sh" - ACTION=="add", SUBSYSTEMS=="scsi", KERNEL=="sg[0-9]*", ATTRS{type}=="5", RUN+="/lib/udev/cdsymlinks.sh" - ACTION=="remove", SUBSYSTEMS=="block", KERNEL=="hd[a-z]", RUN+="/lib/udev/cdsymlinks.sh" - ACTION=="remove", SUBSYSTEMS=="block", KERNEL=="sr[0-9]*", RUN+="/lib/udev/cdsymlinks.sh" - ACTION=="remove", SUBSYSTEMS=="block", KERNEL=="sg[0-9]*", RUN+="/lib/udev/cdsymlinks.sh" ---- snap - -- To get the same device name for CD/DVD symlinks each time you boot, - a rule will be generated during bootup or by executing '/sbin/udevadm trigger'. -- Examples: dvd, cdrom ,cdrw etc. -- If you want to change those links, - modify '/etc/udev/rules.d/70-peristent-cd.rules' to your needs. - -Known issues: -The symlink name is then bound to the hardware pci adress, -if you change your CD/DVD device, you have to check the -/etc/udev/rules.d/70-peristent-net.rules file for correctness. - -====================================== -* Persistent Network names (optional): -====================================== - -- To enable this feature copy in /etc/udev/rules.d - 75-persistent-net-generator.rules.optional - to 75-persistent-net-generator.rules -- To get the same network device name each time you boot, - a rule will be generated during bootup or by executing '/sbin/udevadm trigger'. -- Examples: eth0, eth1, wlan0 etc. -- If you want to change those names, - modify '/etc/udev/rules.d/70-peristent-net.rules' to your needs. -- NAME= determines the name of your network card. Use these names in your - network configuration in rc.conf as well. - -Known issues: -The interface name is then bound to the hardware mac adress, -if you change your network card, you have to check the -/etc/udev/rules.d/70-peristent-net.rules file for correctness. - -==================================== -* Known Problems Hardware: -==================================== - -- BusLogic devices are broken and will cause a freeze during startup -Solution: -This is a kernel bug and no fix has been provided yet. - -- PCMCIA Card readers are not treated as removabel devices. -Solution: -To get access to them with hal's pmount backend add them to /etc/pmount.allow - -==================================== -* Known Problems MOD_AUTOLOAD="yes": -==================================== - ------------------------------------------------------------------------------ -* Sound is not working or modules (eg. parport) are not loaded automatically: ------------------------------------------------------------------------------ -Solution: -- Do you have a clean /etc/modprobe.conf? - - A clean /etc/modprobe.conf is empty. The stock modprobe.conf file - contains nothing -- alsaconf can write output to modprobe.conf. Please keep that in mind. - ---------------------------------------------- -* Devices get mixed up eg. Network/Soundcards ---------------------------------------------- -- Because udev loads all the modules at once, sometimes devices are initialized - in different orders (eg. network cards switch eth0 and eth1, sound cards - the same) - -Solution: -- Load them in MODULES=() array in the order you need them -- eg: MODULES=(moduleA moduleB) - -Second solution for network: -- The "proper" way to configure net interfaces to hold static names within - udev rules. Add lines like these to a custom rules file such as - /etc/udev/rules.d/01-network.rules: - SUBSYSTEM=="net", SYSFS{address}=="aa:bb:cc:dd:ee:ff", NAME="lan0" - SUBSYSTEM=="net", SYSFS{address}=="ff:ee:dd:cc:bb:aa", NAME="wlan0" - -- To get the right mac address use this command: - udevinfo -a -p /sys/class/net/<yourdevice> -- Make sure you use lower-case hex values in your udev rules. -- NAME= determines the name of your network card. Use these names in your - network configuration in rc.conf as well. - -Third solution for network: -- check Persistent Network part - ------------------------------------ -* Network 8139too & 8139cp problem: ------------------------------------ -- Both modules have the same kernel entry, which can cause problems. -Solution: -- Enter the one you need in MODULES=() and blacklist the other one -- eg: MODULES=(!8139cp 8139too) -- The example tells udev to ignore 8139cp module and load 8139too afterwards. - --------------------------------------------------------- -* You need a special loading order to get devices going: --------------------------------------------------------- -- Kernel loads modules in wrong order. -Solution: -- Load them in the correct order in MODULES=() - ------------------------------ -* Module is not autodetected: ------------------------------ -- If your device does not provide a modalias in /sys it cannot be autodetected. -- If modalias is not combined to a kernel module it cannot be autodetected. -Known modules that are not autodetected: -- SCSI CONTROLLER: - scsi_transport_sas ultrastor qlogicfas eata BusLogic pas16 wd7000 sym53c416 - g_NCR5380_mmio fdomain u14-34f dtc initio in2000 imm t128 aha1542 aha152x - atp870u g_NCR5380 NCR53c406a qlogicfas408 megaraid_mm advansys -- NETWORK CARDS: - hp ne de4x5 wd cs89x0 eepro smc9194 seeq8005 ni52 ni65 ac3200 smc-ultra - at1700 hp-plus depca eexpress 82596 de600 eth16i de620 lance ewrk3 e2100 - lp486e 3c501 3c503 3c505 3c507 3c509 3c515 myri10ge -Solution: -- Enter the one you need in MODULES=() - -======================================= -* Known Problems with MOD_AUTOLOAD="no" -======================================= - ------------------------------------------------------------------ -* Modules are not loaded anymore during coldplug or hotplug event ------------------------------------------------------------------ -- Udev is usually responsible for this, but the MOD_AUTOLOAD switch will - now disable it. If you want automatic hot/cold-plugging, turn on - MOD_AUTOLOAD. Otherwise you will have to load all your modules manually, - either with /sbin/modprobe or entries in the MODULES=() array. -Solution: -- For bootup (coldplug) enter this in rc.conf: MODULES=(moduleA moduleB) -- After bootup (hotplug) use this: modprobe <moduleA> - -========================================= -* Known problems for custom kernel users: -========================================= - ----------------------------- -* Udev doesn't start at all: ----------------------------- -- Check Requirements list |