diff options
Diffstat (limited to 'abs/core/system-templates/templates/LCD/antec_fusion/LCDd.conf')
| -rw-r--r--[-rwxr-xr-x] | abs/core/system-templates/templates/LCD/antec_fusion/LCDd.conf | 736 |
1 files changed, 574 insertions, 162 deletions
diff --git a/abs/core/system-templates/templates/LCD/antec_fusion/LCDd.conf b/abs/core/system-templates/templates/LCD/antec_fusion/LCDd.conf index 3719e47..2ff1397 100755..100644 --- a/abs/core/system-templates/templates/LCD/antec_fusion/LCDd.conf +++ b/abs/core/system-templates/templates/LCD/antec_fusion/LCDd.conf @@ -1,7 +1,7 @@ # LCDd.conf -- configuration file for the LCDproc server daemon LCDd # # This file contains the configuration for the LCDd server. -# +# # The format is ini-file-like. It is divided into sections that start at # markers that look like [section]. Comments are all line-based comments, # and are lines that start with '#' or ';'. @@ -10,7 +10,7 @@ # a section called [menu]. Further each driver has a section which # defines how the driver acts. # -# The drivers are activated by specifiying them in a driver= line in the +# The drivers are activated by specifying them in a driver= line in the # server section, like: # # Driver=curses @@ -28,21 +28,29 @@ ## Server section with all kinds of settings for the LCDd server ## [server] +# Where can we find the driver modules ? +# IMPORTANT: Make sure to change this setting to reflect your +# specific setup! Otherwise LCDd won't be able to find +# the driver modules and will thus not be able to +# function properly. +# NOTE: Always place a slash as last character ! +DriverPath=/usr/lib/lcdproc/ + # Tells the server to load the given drivers. Multiple lines can be given. # The name of the driver is case sensitive and determines the section # where to look for further configuration options of the specific driver # as well as the name of the dynamic driver module to load at runtime. -# The latter one can be changed by giving af File= directive in the +# The latter one can be changed by giving a File= directive in the # driver specific section. # # The following drivers are supported: -# bayrad, CFontz, CFontz633, CFontzPacket, curses, CwLnx, EyeboxOne, -# g15, glcdlib, glk, hd44780, icp_a106, imon, IOWarrior, irman, -# joy, lb216,lcdm001, lcterm, lirc,MD8800, ms6931, mtc_s16209x, -# MtxOrb, NoritakeVFD, pyramid, sed1330, sed1520, serialVFD, -# sli, stv5730, svga, t6963, text, tyan, ula200, xosd +# bayrad, CFontz, CFontzPacket, curses, CwLnx, ea65, +# EyeboxOne, g15, glcd, glcdlib, glk, hd44780, icp_a106, imon, imonlcd, +# IOWarrior, irman, joy, lb216, lcdm001, lcterm, lirc, lis, MD8800, +# mdm166a, ms6931, mtc_s16209x, MtxOrb, mx5000, NoritakeVFD, picolcd, +# pyramid, sdeclcd, sed1330, sed1520, serialPOS, serialVFD, shuttleVFD, sli, +# stv5730, svga, t6963, text, tyan, ula200, vlsys_m428, xosd Driver=imonlcd -#Driver=curses # Tells the driver to bind to the given interface Bind=127.0.0.1 @@ -53,72 +61,80 @@ Port=13666 # Sets the reporting level; defaults to 2 (warnings and errors only). #ReportLevel=3 -# Should we report to syslog instead of stderr ? Default: no +# Should we report to syslog instead of stderr ? [default: no; legal: yes, no] #ReportToSyslog=yes +# User to run as. LCDd will drop its root privileges, if any, +# and run as this user instead. +User=nobody + +# The server will stay in the foreground if set to true. +#Foreground=no + +# Hello message: each entry represents a display line; default: builtin +Hello="LinHES" +#Hello=" Welcome to" +#Hello=" LCDproc!" + +# GoodBye message: each entry represents a display line; default: builtin +GoodBye="" +#GoodBye="Thanks for using" +#GoodBye=" LCDproc!" + # Sets the default time in seconds to displays a screen. -WaitTime=5 +WaitTime=10 -# User to run as. LCDd will drop its root priviledges, -# if any, and run as this user instead. -User=nobody +# If set to no, LCDd will start with screen rotation disabled. This has the +# same effect as if the ToggleRotateKey had been pressed. Rotation will start +# if the ToggleRotateKey is pressed. Note that this setting does not turn off +# priority sorting of screens. [default: on; legal: on, off] +#AutoRotate=no # If yes, the the serverscreen will be rotated as a usual info screen. If no, # it will be a background screen, only visible when no other screens are -# active. -ServerScreen=no +# active. The special value 'blank' is similar to no, but only a blank screen +# is displayed. [default: on; legal: on, off, blank] +ServerScreen=blank -# The server will stay in the foreground if set to true. -#Foreground=no +# Set master backlight setting. If set to 'open' a client may control the +# backlight for its own screens (only). [default: open; legal: off, open, on] +#Backlight=open -# Where can we find the driver modules ? -# IMPORTANT: Make sure to change this setting to reflect your -# specific setup! Otherwise LCDd won't be able to find -# the driver modules and will thus not be able to -# function properly. -# NOTE: Always place a slash as last character ! -DriverPath=/usr/lib/lcdproc/ +# Set master heartbeat setting. If set to 'open' a client may control the +# heartbeat for its own screens (only). [default: open; legal: off, open, on] +#Heartbeat=open + +# set title scrolling speed [default: 10; legal: 0-10] +#TitleSpeed=10 # The "...Key=" lines define what the server does with keypresses that -# don't go to any client. -# These are the defaults: +# don't go to any client. The ToggleRotateKey stops rotation of screens, while +# the PrevScreenKey and NextScreenKey go back / forward one screen (even if +# rotation is disabled. +# Assign the key string returned by the driver to the ...Key setting. These +# are the defaults: ToggleRotateKey=Enter PrevScreenKey=Left NextScreenKey=Right #ScrollUpKey=Up #ScrollDownKey=Down -# If you have only 4 keys, you can choose to use this: -#ToggleRotateKey=Enter -#PrevScreenKey=Up -#NextScreenKey=Down - -# If you have only 3 keys, you can choose to use this: -#ToggleRotateKey=Enter -#PrevScreenKey=Up - - ## The menu section. The menu is an internal LCDproc client. ## [menu] # You can configure what keys the menu should use. Note that the MenuKey # will be reserved exclusively, the others work in shared mode. -# The following works excellent with 4 keys or more. +# Up to six keys are supported. The MenuKey (to enter and exit the menu), the +# EnterKey (to select values) and at least one movement keys are required. +# These are the default key assignments: MenuKey=Escape EnterKey=Enter UpKey=Up DownKey=Down -# If you have 6 keys you may define these as well #LeftKey=Left #RightKey=Right -# If you have only 3 keys, you could use something like this: -#MenuKey=Escape -#EnterKey=Enter -#DownKey=Down - - ### Driver sections are below this line, in alphabetical order ### @@ -143,13 +159,14 @@ Device=/dev/ttyS0 Size=20x4 # Set the initial contrast [default: 560; legal: 0 - 1000] Contrast=350 -# Set the initial brightness [default: 255; legal: 0 - 255] -Brightness=255 -# Set the initial off-brightness [default: 0; legal: 0 - 255] +# Set the initial brightness [default: 1000; legal: 0 - 1000] +Brightness=1000 +# Set the initial off-brightness [default: 0; legal: 0 - 1000] # This value is used when the display is normally # switched off in case LCDd is inactive OffBrightness=0 -# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200 or 115200] +# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200, +# 115200] Speed=9600 # Set the firmware version (New means >= 2.0) [default: no; legal: yes, no] NewFirmware=no @@ -159,57 +176,45 @@ Reboot=no -## CrystalFontz633 driver (for CF633 only) ## -[CFontz633] +## CrystalFontz packet driver (for CFA533, CFA631, CFA633 & CFA635) ## +[CFontzPacket] + +# Select the LCD model [default: 633; legal: 533, 631, 633, 635] +Model=633 # Select the output device to use [default: /dev/lcd] -Device=/dev/ttyS0 -# Select the LCD type (size) [default: 16x2] -Size=16x2 +Device=/dev/ttyUSB0 + # Set the initial contrast [default: 560; legal: 0 - 1000] Contrast=350 + # Set the initial brightness [default: 1000; legal: 0 - 1000] Brightness=1000 + # Set the initial off-brightness [default: 0; legal: 0 - 1000] # This value is used when the display is normally # switched off in case LCDd is inactive OffBrightness=50 -# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200] -Speed=19200 -# Set the firmware version (New means >= 2.0) [default: no; legal: yes, no] -# Currently this flag is not in use, there is no such thing as NewFirmware. ;=) -#NewFirmware=no -# Reinitialize the LCD's BIOS [default: no; legal: yes, no] -# I want to reboot the LCD to make sure we start from a known state + +# Reinitialize the LCD's BIOS on driver start. [default: no; legal: yes, no] Reboot=yes +# Enable the USB flag if the device is connected to an USB port. For +# serial ports leave it disabled. [default: no; legal: yes, no] +#USB=yes +# Very old 633 firmware versions do not support partial screen updates using +# 'Send Data to LCD' command (31). For those devices it may be necessary to +# enable this flag. [default: no; legal: yes, no] +#OldFirmware=yes -## CrystalFontz packet driver (for CF631, CF633 & CF635) ## -[CFontzPacket] +# Override the LCD size known for the selected model. Usually setting this +# value should not be necessary. +#Size=20x4 -# Select the LCD model [default: 633; legal: 631, 633, 635] -Model=635 -# Select the output device to use [default: /dev/lcd] -Device=/dev/ttyUSB0 -# Select the LCD size [default: depending on model: 635: 20x4, 631: 20x2, 633: 16x2] -Size=20x4 -# Set the initial contrast [default: 560; legal: 0 - 1000] -Contrast=350 -# Set the initial brightness [default: 1000; legal: 0 - 1000] -Brightness=1000 -# Set the initial off-brightness [default: 0; legal: 0 - 1000] -# This value is used when the display is normally -# switched off in case LCDd is inactive -OffBrightness=50 -# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200] -Speed=115200 -# Set the firmware version (New means >= 2.0) [default: no; legal: yes, no] -# Currently this flag is not in use, there is no such thing as NewFirmware. ;=) -#NewFirmware=no -# Reinitialize the LCD's BIOS [default: no; legal: yes, no] -# I want to reboot the LCD to make sure we start from a known state -Reboot=yes +# Override the default communication speed known for the selected model. +# Default value depends on model [legal: 19200, 115200] +#Speed=115200 @@ -232,20 +237,27 @@ Size=20x4 TopLeftX=7 TopLeftY=7 -# use ASC symbols for icons & bars [default: no; legal, yes, no] +# use ASC symbols for icons & bars [default: no; legal: yes, no] UseACS=no +# draw Border [default: yes; legal: yes, no] +DrawBorder=yes + ## Cwlinux driver ## [CwLnx] -# Select the LCD model [default: 12232; legal: 12232, 1602] +# Select the LCD model [default: 12232; legal: 12232, 12832, 1602] Model=12232 + # Select the output device to use [default: /dev/lcd] Device=/dev/ttyUSB0 -# Select the LCD size [default: depending on model: 12232: 20x4, 1602: 16x2] +# Select the LCD size. Default depends on model: +# 12232: 20x4 +# 12832: 21x4 +# 1602: 16x2 Size=20x4 # Set the communication speed [default: 19200; legal: 9600, 19200] @@ -274,12 +286,29 @@ Keypad=yes # KeyMap_E=Enter # KeyMap_F=Escape -# keypad_test_mode permits to test keypad assignement +# keypad_test_mode permits one to test keypad assignment # Default value is no #keypad_test_mode=yes +## ea65 driver for the display in AOpen XC Cube AV EA65 media barebones ## +[ea65] + +# Device is fixed /dev/ttyS1 +# Width and Height are fixed 9x1 + +# As the VFD is self luminescent we don't have a backlight +# But we can use the backlight functions to control the front LEDs +# Brightness 0 to 299 -> LEDs off +# Brightness 300 to 699 -> LEDs half bright +# Brightness 700 to 1000 -> LEDs full bright +Brightness=500 +# OffBrightness is the the value used for the 'backlight off' state +OffBrightness=0 + + + ## EyeboxOne driver ## [EyeboxOne] @@ -314,12 +343,98 @@ EscapeKey=P keypad_test_mode=no + ## g15 driver for Logitech G15 Keyboard LCDs ## [g15] # Display size (currently unused) size=20x5 + + +## glcd generic graphical display driver +[glcd] +# Select what type of connection. See documentation for types. +ConnectionType=t6963 + +# Width and height of the display in pixel. The supported sizes may depend on +# the ConnectionType. [default: 128x64; legal: 1x1 - 640x480] +#Size=128x64 + +# Width and height of a character cell in pixels. This value is only used if +# the driver has been compiled with FreeType and it is enabled. Otherwise the +# default 6x8 cell is used. +#CellSize=12x16 + +# If LCDproc has been compiled with FreeType 2 support this option can be used +# to turn if off intentionally. [default: yes; legal: yes, no] +#useFT2=no + +# Path to font file to use for FreeType rendering. This font must be monospace +# and should contain some special Unicode characters like arrows (Andale Mono +# is recommended and can be fetched at http://corefonts.sf.net). +#normal_font=/usr/local/lib/X11/fonts/TTF/andalemo.ttf + +# Some fonts miss the Unicode characters used to represent icons. In this case +# the built-in 5x8 font can used if this option is turned off. [default: yes; +# legal: yes, no] +#fontHasIcons=no + +# Set the initial contrast if supported by connection type. +# [default: 600; legal: 0 - 1000] +#Contrast=600 + +# Set brightness of the backlight if the backlight is switched 'on'. +# [default: 800; legal: 0 - 1000] +#Brightness=1000 + +# Set brightness of the backlight if the backlight is switched 'off'. Set this +# to zero to completely turn off the backlight. [default: 100; legal: 0 - 1000] +#OffBrightness=0 + +# Time (ms) from first key report to first repeat. Set to 0 to disable repeated +# key reports. [default: 500; legal: 0 - 3000] +#KeyRepeatDelay=500 + +# Time (ms) between repeated key reports. Ignored if KeyRepeatDelay is disabled +# (set to zero). [default: 300; legal: 0 - 3000] +#KeyRepeatInterval=300 + +# Assign key strings to keys. There may be up to 16 keys numbered 'A' to 'Z'. +# By default keys 'A' to 'F' are assigned Up, Down, Left, Right, Enter, Escape. +KeyMap_A=Up +KeyMap_B=Down +KeyMap_C=Enter +KeyMap_D=Escape + +# t6963: Parallel port to use [default: 0x378; legal: 0x200 - 0x400] +#Port=0x378 + +# t6963: Use LPT port in bi-directional mode. This should work on most LPT port +# and is required for proper timing! [default: yes; legal: yes, no] +#bidirectional=yes + +# t6963: Insert additional delays into reads / writes. [default: no; +# legal: yes, no] +#delayBus=no + +# serdisplib: Name of the underlying serdisplib driver, e.g. ctinclud. See +# serdisplib documentation for details. +serdisp_name=t6963 + +# serdisplib: The display device to use, e.g. serraw:/dev/ttyS0, +# parport:/dev/parport0 or USB:07c0/1501. +serdisp_device=/dev/ppi0 + +# serdisplib: Options string to pass to serdisplib during initialization. Use +# this to set any display related options (e.g. wiring). The display size is +# always set based on the Size configured above! By default, no options are +# set. +# Important: The value must be quoted as it contains equal signs! +#serdisp_options="INVERT=1" + + + ## glcdlib meta driver for graphical LCDs ## [glcdlib] @@ -330,40 +445,39 @@ size=20x5 Driver=noritake800 # no=use graphlcd bitmap fonts (they have only one size / font file) -# yes=use fonts supported by FreeType2 (needs Freetype2 support in libglcdprocdriver and its dependants) +# yes=use fonts supported by FreeType2 (needs Freetype2 support in +# libglcdprocdriver and its dependants) UseFT2=yes # text resolution in fixed width characters [default: 16x4] -# (if it won't fit according to available physical pixel resolutioni -# and the minimum available font face size in pixels, then +# (if it won't fit according to available physical pixel resolution +# and the minimum available font face size in pixels, then # 'DebugBorder' will automatically be turned on) TextResolution=20x4 # path to font file to use FontFile=/usr/share/fonts/corefonts/courbd.ttf - ## these only apply if UseFT2=yes: # character encoding to use CharEncoding=iso8859-2 -# minumum size in pixels in which fonts should be rendered +# minimum size in pixels in which fonts should be rendered MinFontFaceSize=7x12 - ## optional: -Brightness=50 # Brightness (in %) if applicable -Contrast=50 # Contrast (in %) if applicable -Backlight=no # Backlight if applicable -UpsideDown=no # flip image upside down -Invert=no # invert light/dark pixels -ShowDebugFrame=no # turns on/off 1 pixel thick debugging - # border whithin the usable text area, - # for setting up TextResolution and - # MinFontFaceSize (if using FT2); -ShowBigBorder=no # border around the unused area -ShowThinBorder=yes # border around the unused area +Brightness=50 # Brightness (in %) if applicable +Contrast=50 # Contrast (in %) if applicable +Backlight=no # Backlight if applicable +UpsideDown=no # flip image upside down +Invert=no # invert light/dark pixels +ShowDebugFrame=no # turns on/off 1 pixel thick debugging + # border within the usable text area, + # for setting up TextResolution and + # MinFontFaceSize (if using FT2); +ShowBigBorder=no # border around the unused area +ShowThinBorder=yes # border around the unused area PixelShiftX=0 PixelShiftY=2 @@ -389,10 +503,10 @@ Speed=19200 # Select what type of connection. See documentation for types. ConnectionType=4bit -# Port where the LPT is. Usual values are 0x278, 0x378 and 0x3BC +# Port where the LPT is. Usual value are: 0x278, 0x378 and 0x3BC Port=0x378 -# Device of the serial interface (default is /dev/lcd) +# Device of the serial interface [default: /dev/lcd] Device=/dev/ttyS0 # Bitrate of the serial port (0 for interface default) @@ -402,8 +516,18 @@ Speed=0 # You may also need to configure the keypad layout further on in this file. Keypad=no -# set the initial contrast (for bwctusb only) [default: 0; legal: 0 - 1000] -Contrast=0 +# Set the initial contrast (bwctusb, lcd2usb, and usb4all) +# [default: 800; legal: 0 - 1000] +#Contrast=0 + +# Set brightness of the backlight (lcd2usb and usb4all): +# Brightness is the brightness while the backlight is set to 'on'. +# [default: 800; legal: 0 - 1000] +#Brightness=1000 + +# OffBrightness is the brightness while the backlight is set to 'off'. +# [default: 300; legal: 0 - 1000] +#OffBrightness=0 # If you have a switchable backlight. Backlight=no @@ -412,9 +536,9 @@ Backlight=no # be able to control it with the lcdproc OUTPUT command OutputPort=no -# Specifies if the last line is pixel addressable or it controls an -# underline effect. [default: true (= pixel addressable); legal: yes, no] -#Lastline=true +# Specifies if the last line is pixel addressable (yes) or it controls an +# underline effect (no). [default: yes; legal: yes, no] +#Lastline=yes # Specifies the size of the LCD. # In case of multiple combined displays, this should be the total size. @@ -424,20 +548,36 @@ Size=20x4 # Vspan=2,2 means both displays have 2 lines. #vspan=2,2 -# If you have an HD66712, a KS0073 or an other 'almost HD44780-compatible', +# If you have an HD66712, a KS0073 or another 'almost HD44780-compatible', # set this flag to get into extended mode (4-line linear). -# This flag is NOT the old obsolete Extended option. #ExtendedMode=yes +# In extended mode, on some controllers like the ST7036 (in 3 line mode) +# the next line in DDRAM won't start 0x20 higher. [default: 0x20] +#LineAddress=0x10 + # Character map to to map ISO-8859-1 to the LCD's character set -# [default: hd44780_default; legal: hd44780_default, ea_ks0073 ] -Charmap=hd44780_default +# [default: hd44780_default; legal: hd44780_default, hd44780_euro, ea_ks0073, +# sed1278f_0b, hd44780_koi8_r, hd44780_cp1251, hd44780_8859_5, upd16314 ] +# (hd44780_koi8_r, hd44780_cp1251, hd44780_8859_5 and upd16314 are possible if +# compiled with additional charmaps) +CharMap=hd44780_default # If your display is slow and cannot keep up with the flow of data from # LCDd, garbage can appear on the LCDd. Set this delay factor to 2 or 4 # to increase the delays. Default: 1. #DelayMult=2 +# Some displays (e.g. vdr-wakeup) need a message from the driver to that it +# is still alive. When set to a value bigger then null the character in the +# upper left corner is updated every <KeepAliveDisplay> seconds. Default: 0. +#KeepAliveDisplay=0 + +# If you experience occasional garbage on your display you can use this +# option as workaround. If set to a value bigger than null it forces a +# full screen refresh <RefreshDiplay> seconds. Default: 0. +#RefreshDisplay=5 + # You can reduce the inserted delays by setting this to false. # On fast PCs it is possible your LCD does not respond correctly. # Default: true. @@ -468,14 +608,17 @@ Device=/dev/ttyS1 # display dimensions Size=20x4 -# serial number [exactly as listed by usbview] +# serial number. Must be exactly as listed by usbview # (if not given, the 1st IOWarrior found gets used) #SerialNumber=00000674 -# Specifies if the last line is pixel addressable or it controls an -# underline effect. [default: true (= pixel addressable); legal: yes, no] -#Lastline=true +# If you have an HD66712, a KS0073 or another 'almost HD44780-compatible', +# set this flag to get into extended mode (4-line linear). +#ExtendedMode=yes +# Specifies if the last line is pixel addressable (yes) or it controls an +# underline effect (no). [default: yes; legal: yes, no] +#Lastline=yes @@ -484,28 +627,53 @@ Size=20x4 # select the device to use Device=/dev/lcd0 -# Protocl=0 # display dimensions Size=16x2 -## Soundgraph/Ahanix/Silverstone/Uneed/Accent iMON driver ## +# Character map to to map ISO-8859-1 to the displays character set. +# [default: none; legal: none, hd44780_euro, upd16314, hd44780_koi8_r, +# hd44780_cp1251, hd44780_8859_5 ] (upd16314, hd44780_koi8_r, +# hd44780_cp1251, hd44780_8859_5 are possible if compiled with additional +# charmaps) +CharMap=hd44780_euro + +## Soundgraph iMON LCD ## [imonlcd] +# Specify which iMon protocol should be used +# [legal: 0, 1; default: 0] +# Choose 0 for 15c2:ffdc device, +# Choose 1 for 15c2:0038 device +Protocol=0 + +# Set the exit behavior [legal: 0-2; default: 1] +# 0 means leave shutdown message, +# 1 means show the big clock, +# 2 means blank device +#OnExit=2 + +# Select the output device to use [default: /dev/lcd0] +Device=/dev/lcd0 -# select the device to use -Device=/dev/lcd +# Select the displays contrast [default: 200; legal: 0-1000] Contrast=200 -#Protocl=0 -# display dimensions -#Size=16x2 +# Specify the size of the display in pixels [default: 96x16] +#Size=96x16 + +# Set the backlight state [default: on; legal: on, off] +#Backlight=on +# Set the disc mode [legal: 0,1; default: 0] +# 0 => spin the "slim" disc - two disc segments, +# 1 => their complement spinning; +#DiscMode=0 ## IrMan driver ## [IrMan] -#if in trouble with IrMan, try Lirc emulator for IrMan +# in case of trouble with IrMan, try the Lirc emulator for IrMan # Select the input device to use #Device=/dev/irman @@ -515,6 +683,20 @@ Contrast=200 +## IRtrans driver ## +[irtrans] + +# Does the device have a backlight? [default: no; legal: yes, no] +#Backlight=no + +# IRTrans device to connect to [default: localhost] +#Hostname=localhost + +# display dimensions +Size=16x2 + + + ## Joystick driver ## [joy] @@ -591,6 +773,30 @@ Size=16x2 +## LIS MCE 2005 driver ## +[lis] + +# Set the initial brightness [default: 1000; legal: 0 - 1000] +# 0-250 = 25%, 251-500 = 50%, 501-750 = 75%, 751-1000 = 100% +#Brightness=1000 + +# Columns by lines [default: 20x2] +#Size=20x2 + +# USB Vendor ID [default: 0x0403] +# Change only if testing a compatible device. +#VendorID=0x0403 + +# USB Product ID [default: 0x6001] +# Change only if testing a compatible device. +#ProductID=0x6001 + +# Specifies if the last line is pixel addressable (yes) or it only controls an +# underline effect (no). [default: yes; legal: yes, no] +#Lastline=yes + + + ##The driver for the VFD of the Medion MD8800 PC ## [MD8800] # device to use [default: /dev/ttyS1] @@ -608,6 +814,18 @@ OffBrightness=50 +## Futuba MDM166A Display +[mdm166a] +# Show self-running clock after LCDd shutdown +# Possible values: [default: no; legal: no, small, big] +Clock=big +# Dim display, no dimming gives full brightness [default: no, legal: yes, no] +Dimming=no +# Dim display in case LCDd is inactive [default: no, legal: yes, no] +OffDimming=yes + + + ## MSI MS-6931 driver for displays in 1HU servers ## [ms6931] @@ -642,23 +860,30 @@ Device=/dev/ttyS0 # Set the display size [default: 20x4] Size=20x4 -# Switch on the backlight? [default: yes] -# NOTE: The driver will ignore this if the display is a vfd or vkd -# as they crash if the backlight is turned off -Backlight=yes +# Set the display type [default: lcd; legal: lcd, lkd, vfd, vkd] +Type=lkd # Set the initial contrast [default: 480] # NOTE: The driver will ignore this if the display # is a vfd or vkd as they don't have this feature -Contrast=800 +Contrast=480 + +# Some old displays do not have an adjustable backlight but only can +# switch the backlight on/off. If you experience randomly appearing block +# characters, try setting this to false. [default: yes; legal: yes, no] +hasAdjustableBacklight=no + +# Set the initial brightness [default: 1000; legal: 0 - 1000] +Brightness=1000 +# Set the initial off-brightness [default: 0; legal: 0 - 1000] +# This value is used when the display is normally +# switched off in case LCDd is inactive +OffBrightness=0 # Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200] Speed=19200 -# Set the display type [default: lcd; legal: lcd, lkd, vfd, vkd] -Type=lkd - -# The following table translates from MtxOrb key letters to logical key namess. +# The following table translates from MtxOrb key letters to logical key names. # By default no keys are mapped, meaning the keypad is not used at all. #KeyMap_A=Left #KeyMap_B=Right @@ -677,22 +902,107 @@ keypad_test_mode=no +## mx5000 driver for LCD display on the Logitech MX5000 keyboard ## +[mx5000] + +# Select the output device to use [default: /dev/hiddev0] +Device = /dev/hiddev0 +# Time to wait in ms after the refresh screen has been sent [default: 1000] +WaitAfterRefresh = 1000 + + + ## Noritake VFD driver ## [NoritakeVFD] -# device where the VFD is. Usual values are /dev/ttyS0 and /dev/ttyS1 [default: /dev/lcd] +# device where the VFD is. Usual values are /dev/ttyS0 and /dev/ttyS1 +# [default: /dev/lcd] Device=/dev/ttyS0 - # Specifies the size of the LCD. Size=20x4 - -# set the brightness -Brightness=255 - +# Set the initial brightness [default: 1000; legal: 0 - 1000] +Brightness=1000 +# Set the initial off-brightness [default: 0; legal: 0 - 1000] +# This value is used when the display is normally +# switched off in case LCDd is inactive +OffBrightness=50 # set the serial port speed [default: 9600, legal: 1200, 2400, 9600, 19200, 115200] Speed=9600 +# Set serial data parity [default: 0; legal: 0-2 ] +# Meaning: 0(=none), 1(=odd), 2(=even) +Parity=0 +# re-initialize the VFD [default: no; legal: yes, no] +Reboot=no + -# re-initialize VFD ? -#Reboot=yes + +## Mini-box.com picoLCD (usblcd) driver ## +[picolcd] + +# KeyTimeout is only used if the picoLCD driver is built with libusb-0.1. When +# built with libusb-1.0 key and IR data is input asynchronously so there is no +# need to wait for the USB data. +# KeyTimeout is the time in ms that LCDd spends waiting for a key press before +# cycling through other duties. Higher values make LCDd use less CPU time and +# make key presses more detectable. Lower values make LCDd more responsive +# but a little prone to missing key presses. 500 (.5 second) is the default +# and a balanced value. [default: 500; legal: 0 - 1000] +KeyTimeout=500 + +# Key auto repeat is only available if the picoLCD driver is built with +# libusb-1.0. Use KeyRepeatDelay and KeyRepeatInterval to configure key auto +# repeat. +# +# Key auto repeat delay (time in ms from first key report to first repeat). Use +# zero to disable auto repeat. [default: 300; legal: 0 - 3000] +KeyRepeatDelay=300 + +# Key auto repeat interval (time in ms between repeat reports). Only used if +# KeyRepeatDelay is not zero. [default: 200; legal: 0 - 3000] +KeyRepeatInterval=200 + +# Sets the initial state of the backlight upon start-up. +# [default: on; legal: on, off] +#Backlight=on + +# Set the initial brightness [default: 1000; legal: 0 - 1000]. Works only +# with the 20x4 device +Brightness=1000 + +# Set the brightness while the backlight is 'off' [default: 0; legal: 0 - 1000]. +# Works only with the 20x4 device. +#OffBrightness=0 + +# Set the initial contrast [default: 1000; legal: 0 - 1000] +Contrast=1000 + +# Link the key lights to the backlight? [default: on; legal: on, off] +#LinkLights=off + +# Light the keys? [default: on; legal: on, off] +Keylights=on + +# If Keylights is on, the you can unlight specific keys below: +# Key0 is the directional pad. Key1 - Key5 correspond to the F1 - F5 keys. +# There is no LED for the +/- keys. This is a handy way to indicate to users +# which keys are disabled. [default: on; legal: on, off] +Key0Light=on +Key1Light=on +Key2Light=on +Key3Light=on +Key4Light=on +Key5Light=on + +# Host name or IP address of the LIRC instance that is to receive IR codes +# If not set, or set to an empty value, IR support is disabled. +#LircHost=127.0.0.1 + +# UDP port on which LIRC is listening [default: 8765; legal: 1 - 65535] +LircPort=8765 + +# Threshold in jiffies of synthesized gap that triggers flushing the IR data +# to lirc [default: 100 ; max: 32767 ] +# 100 means 6.1ms. legal: 16 - 32767; Use 0 to disable. +LircFlushThreshold=100 @@ -704,16 +1014,28 @@ Device=/dev/ttyUSB0 +## SDEC driver for Watchguard Firebox ## +[sdeclcd] +# No options + + + ## Seiko Epson 1330 driver ## [sed1330] # Port where the LPT is. Common values are 0x278, 0x378 and 0x3BC Port=0x378 -# Type of LCD module (legal: G321D, G121C, G242C, G191D, G2446) -# Note: G321D is the only one that is tested currently. +# Type of LCD module (legal: G321D, G121C, G242C, G191D, G2446, SP14Q002) +# Note: Currently only tested with G321D & SP14Q002. Type=G321D +# Width x Height of a character cell in pixels [legal: 6x7 - 8x16; default: 6x10] +CellSize=6x10 + +# Select what type of connection [legal: classic, bitshaker; default: classic] +ConnectionType=classic + ## Seiko Epson 1520 driver ## @@ -722,6 +1044,39 @@ Type=G321D # Port where the LPT is. Usual values are 0x278, 0x378 and 0x3BC Port=0x378 +# Select the interface type (wiring) for the display. Supported values are +# 68 for 68-style connection (RESET level high) and 80 for 80-style connection +# (RESET level low). [legal: 68, 80; default: 80] +InterfaceType=80 + +# On fast machines it may be necessary to slow down transfer to the display. +# If this value is set to zero, delay is disabled. Any value greater than +# zero slows down each write by one microsecond. [legal: 0-1000; default: 1] +DelayMult=0 + +# The original wiring used an inverter to drive the control lines. If you do +# not use an inverter set haveInverter to no. [default: yes; legal: yes, no] +haveInverter=no + + + +## serial POS display driver ## +[serialPOS] + +# Device to use in serial mode [default: /dev/lcd] +Device=/dev/lcd + +# Specifies the size of the display in characters. [default: 16x2] +Size=16x2 + +# Set the communication protocol to use with the POS display. +# [default: AEDEX; legal: IEE, Epson, Emax, IBM, LogicControls, Ultimate] +Type=AEDEX + +# communication baud rate with the display [default: 9600; legal: 1200, 2400, +# 19200, 115200] +Speed=9600 + ## Serial VFD driver ## @@ -733,18 +1088,29 @@ Port=0x378 # 1 KD Rev 2.1. # 2 Noritake VFDs (*). # 3 Futaba VFDs -# (* most should work, not testet yet.) +# 4 IEE S03601-95B +# 5 IEE S03601-96-080 (*) +# 6 Futaba NA202SD08FA (allmost IEE compatible) +# 7 Samsung 20S207DA4 and 20S207DA6 +# 8 Nixdorf BA6x / VT100 +# (* most should work, not tested yet.) Type=0 -# "no" if display connected serial, "yes" if connected parallel. [default: no(=serial)] +# "no" if display connected serial, "yes" if connected parallel. [default: no] +# I.e. serial by default use_parallel=no -# Number of Custom-Characters [default: displaytype dependent] +# Number of Custom-Characters. default is display type dependent #Custom-Characters=0 -# Portaddress where the LPT is. Used in parallelmode only. Usual values are 0x278, 0x378 and 0x3BC +# Portaddress where the LPT is. Used in parallel mode only. Usual values are +# 0x278, 0x378 and 0x3BC. Port=0x378 +# Set parallel port timing delay (us). Used in parallel mode only. +# [default: 2; legal: 0 - 255] +#PortWait=2 + # Device to use in serial mode. Usual values are /dev/ttyS0 and /dev/ttyS1 Device=/dev/ttyS1 @@ -768,6 +1134,12 @@ Speed=9600 +## shuttleVFD driver ## +[shuttleVFD] +# No options + + + ## stv5730 driver ## [stv5730] @@ -775,11 +1147,35 @@ Speed=9600 Port=0x378 +[SureElec] + +# Port the device is connected to (by default first USB serial port) +Device=/dev/ttyUSB0 + +# Edition level of the device (can be 1, 2 or 3) [default: 2] +#Edition=1 + +# set display size +# Note: The size can be obtained directly from device for edition 2 & 3. +#Size=16x2 + +# Set the initial contrast [default: 480; legal: 0 - 1000] +#Contrast=200 + +# Set the initial brightness [default: 480; legal: 1 - 1000] +#Brightness=480 + +# Set the initial off-brightness [default: 100; legal: 1 - 1000] +# This value is used when the display is normally +# switched off in case LCDd is inactive +#OffBrightness=100 + ## SVGAlib driver ## [svga] -# svgalib mode to use [default: G320x240x256; legal: supported svgalib modes] +# svgalib mode to use [default: G320x240x256 ] +# legal values are supported svgalib modes #Mode=G640x480x256 # set display size [default: 20x4] @@ -809,17 +1205,21 @@ Size=20x4 ## Toshiba T6963 driver ## [t6963] -# set display size [default: 20x6] -Size=20x6 +# set display size in pixels [default: 128x64] +Size=128x64 # port to use [default: 0x378; legal: 0x200 - 0x400] Port=0x378 -# Is ECP mode on? [default: yes; legal: yes, no] -#ECPlpt=yes +# Use LPT port in bi-directional mode. This should work on most LPT port and +# is required for proper timing! [default: yes; legal: yes, no] +#bidirectional=yes -# Use graphics? [default: no; legal: yes, no] -#graphic=no +# Insert additional delays into reads / writes. [default: no; legal: yes, no] +#delayBus=no + +# Clear graphic memory on start-up. [default: no; legal: yes, no] +#ClearGraphic=no @@ -866,18 +1266,30 @@ Size=20x4 # Select the output device to use [default: /dev/lcd] Device=/dev/lcd -# Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200, 38400, 57600, 115200] +# Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200, +# 38400, 57600, 115200] Speed=19200 +## vlsys_m428 for VFD/IR combination in Moneual MonCaso 320 ## +[vlsys_m428] + +# Select the output device to use [default: /dev/ttyUSB0] +#Device=/dev/ttyUSB0 + + + ## OnScreen Display using libxosd ## [xosd] # set display size [default: 20x4] Size=20x4 -# font to use -Font=-*-terminus-*-r-*-*-*-320-*-*-*-*-* +# Offset in pixels from the top-left corner of the monitor [default: 0x0] +Offset=200x200 + +# X font to use, in XLFD format, as given by "xfontsel" +Font=-*-clean-*-*-*-*-*-160-*-*-*-*-*-* # EOF |