diff options
Diffstat (limited to 'abs/not_built/extra/apcupsd')
| -rw-r--r-- | abs/not_built/extra/apcupsd/PKGBUILD | 38 | ||||
| -rwxr-xr-x | abs/not_built/extra/apcupsd/apcupsd | 44 | ||||
| -rw-r--r-- | abs/not_built/extra/apcupsd/apcupsd.conf | 325 | ||||
| -rw-r--r-- | abs/not_built/extra/apcupsd/run | 4 |
4 files changed, 411 insertions, 0 deletions
diff --git a/abs/not_built/extra/apcupsd/PKGBUILD b/abs/not_built/extra/apcupsd/PKGBUILD new file mode 100644 index 0000000..ad57d1a --- /dev/null +++ b/abs/not_built/extra/apcupsd/PKGBUILD @@ -0,0 +1,38 @@ +# $Id: PKGBUILD,v 1.17 2009/01/19 10:34:32 sergej Exp $ +# Maintainer: Sergej Pupykin <sergej@aur.archlinux.org> +# Maintainer: Todd Musall <tmusall@comcast.net> + +pkgname=apcupsd +pkgver=3.14.8 +pkgrel=1 +pkgdesc="Apcupsd can be used for power mangement and controlling most of APC's UPS models on Unix and Windows machines." +arch=(i686 x86_64) +url="http://www.apcupsd.org" +license=('GPL') +depends=('gcc-libs' 'gd' 'gconf') +makedepends=('pkgconfig') +backup=(etc/apcupsd/apcupsd.conf etc/apcupsd/hosts.conf \ + etc/apcupsd/multimon.conf) +source=(http://switch.dl.sf.net/sourceforge/apcupsd/$pkgname-$pkgver.tar.gz \ + apcupsd + apcupsd.conf + run) + +build() { + cd $startdir/src/$pkgname-$pkgver + ./configure --prefix=/usr --enable-cgi --enable-usb --enable-net \ + --with-upstype=usb --with-upscable=usb \ + --with-serial-dev=/dev/usb/hid/hiddev[0-9] \ + --enable-pthreads --enable-gapcmon + make || return 1 + make DESTDIR=$startdir/pkg install || return 1 + install -D -m755 ../apcupsd $startdir/pkg/etc/rc.d/apcupsd && \ + chmod 755 $startdir/pkg/sbin/* + cp ../apcupsd.conf $startdir/pkg/etc/apcupsd/ + mkdir -p $startdir/pkg/etc/sv/apcupsd/supervise + install -D -m755 ../run $startdir/pkg/etc/sv/apcupsd +} +md5sums=('cd17f0a903dc2220e55ed54e242359d2' + '5eae3c4d921eeb81798a0250fe3dd111' + '2f533aec32c9445510bb2127b453b175' + '32ae73bc096c1d0982c12d8ec46abee2') diff --git a/abs/not_built/extra/apcupsd/apcupsd b/abs/not_built/extra/apcupsd/apcupsd new file mode 100755 index 0000000..3cd5c9d --- /dev/null +++ b/abs/not_built/extra/apcupsd/apcupsd @@ -0,0 +1,44 @@ +#!/bin/bash + +. /etc/rc.conf +. /etc/rc.d/functions + +PID=`pidof -o %PPID /sbin/apcupsd` +case "$1" in + start) + stat_busy "Starting APCUPSD Daemon" + rm -f /etc/apcupsd/powerfail + rm -f /etc/nologin + [ -z "$PID" ] && /sbin/apcupsd -f /etc/apcupsd/apcupsd.conf + if [ $? -gt 0 ]; then + stat_fail + else + PID=`pidof -o %PPID /sbin/apcupsd` + echo $PID > /var/run/apcupsd.pid + add_daemon apcupsd + stat_done + fi + ;; + stop) + stat_busy "Stopping APCUPSD Daemon" + [ ! -z "$PID" ] && kill $PID &> /dev/null + if [ $? -gt 0 ]; then + stat_fail + else + rm /var/run/apcupsd.pid + rm_daemon apcupsd + stat_done + fi + ;; + restart) + $0 stop + sleep 2 + $0 start + ;; + status) + /sbin/apcaccess status + ;; + *) + echo "usage: $0 {start|stop|restart|status}" +esac +exit 0 diff --git a/abs/not_built/extra/apcupsd/apcupsd.conf b/abs/not_built/extra/apcupsd/apcupsd.conf new file mode 100644 index 0000000..dd60889 --- /dev/null +++ b/abs/not_built/extra/apcupsd/apcupsd.conf @@ -0,0 +1,325 @@ +## apcupsd.conf v1.1 ## +# +# for apcupsd release 3.14.5 (10 January 2009) - unknown +# +# "apcupsd" POSIX config file + +# +# ========= General configuration parameters ============ +# + +# UPSNAME xxx +# Use this to give your UPS a name in log files and such. This +# is particulary useful if you have multiple UPSes. This does not +# set the EEPROM. It should be 8 characters or less. +#UPSNAME + +# UPSCABLE <cable> +# Defines the type of cable connecting the UPS to your computer. +# +# Possible generic choices for <cable> are: +# simple, smart, ether, usb +# +# Or a specific cable model number may be used: +# 940-0119A, 940-0127A, 940-0128A, 940-0020B, +# 940-0020C, 940-0023A, 940-0024B, 940-0024C, +# 940-1524C, 940-0024G, 940-0095A, 940-0095B, +# 940-0095C, M-04-02-2000 +# +UPSCABLE usb + +# To get apcupsd to work, in addition to defining the cable +# above, you must also define a UPSTYPE, which corresponds to +# the type of UPS you have (see the Description for more details). +# You must also specify a DEVICE, sometimes referred to as a port. +# For USB UPSes, please leave the DEVICE directive blank. For +# other UPS types, you must specify an appropriate port or address. +# +# UPSTYPE DEVICE Description +# apcsmart /dev/tty** Newer serial character device, +# appropriate for SmartUPS models using +# a serial cable (not USB). +# +# usb <BLANK> Most new UPSes are USB. A blank DEVICE +# setting enables autodetection, which is +# the best choice for most installations. +# +# net hostname:port Network link to a master apcupsd +# through apcupsd's Network Information +# Server. This is used if you don't have +# a UPS directly connected to your computer. +# +# snmp hostname:port:vendor:community +# SNMP Network link to an SNMP-enabled +# UPS device. Vendor is the MIB used by +# the UPS device: can be "APC", "APC_NOTRAP" +# or "RFC" where APC is the powernet MIB, +# "APC_NOTRAP" is powernet with SNMP trap +# catching disabled, and RFC is the IETF's +# rfc1628 UPS-MIB. You usually want "APC". +# Port is usually 161. Community is usually +# "private". +# +# dumb /dev/tty** Old serial character device for use +# with simple-signaling UPSes. +# +# pcnet ipaddr:username:passphrase +# PowerChute Network Shutdown protocol +# which can be used as an alternative to SNMP +# with AP9617 family of smart slot cards. +# ipaddr is the IP address of the UPS mgmt +# card. username and passphrase are the +# credentials for which the card has been +# configured. +# +UPSTYPE usb +DEVICE /dev/usb/hid/hiddev[0-9] + +# POLLTIME <int> +# Interval (in seconds) at which apcupsd polls the UPS for status. This +# setting applies both to directly-attached UPSes (UPSTYPE apcsmart, usb, +# dumb) and networked UPSes (UPSTYPE net, snmp). Lowering this setting +# will improve apcupsd's responsiveness to certain events at the cost of +# higher CPU utilization. The default of 60 is appropriate for most +# situations. +#POLLTIME 60 + +# LOCKFILE <path to lockfile> +# Path for device lock file. Not used on Win32. +LOCKFILE /var/lock + +# SCRIPTDIR <path to script directory> +# Directory in which apccontrol and event scripts are located. +SCRIPTDIR /etc/apcupsd + +# PWRFAILDIR <path to powerfail directory> +# Directory in which to write the powerfail flag file. This file +# is created when apcupsd initiates a system shutdown and is +# checked in the OS halt scripts to determine if a killpower +# (turning off UPS output power) is required. +PWRFAILDIR /etc/apcupsd + +# NOLOGINDIR <path to nologin directory> +# Directory in which to write the nologin file. The existence +# of this flag file tells the OS to disallow new logins. +NOLOGINDIR /etc + + +# +# ======== Configuration parameters used during power failures ========== +# + +# The ONBATTERYDELAY is the time in seconds from when a power failure +# is detected until we react to it with an onbattery event. +# +# This means that, apccontrol will be called with the powerout argument +# immediately when a power failure is detected. However, the +# onbattery argument is passed to apccontrol only after the +# ONBATTERYDELAY time. If you don't want to be annoyed by short +# powerfailures, make sure that apccontrol powerout does nothing +# i.e. comment out the wall. +ONBATTERYDELAY 6 + +# +# Note: BATTERYLEVEL, MINUTES, and TIMEOUT work in conjunction, so +# the first that occurs will cause the initation of a shutdown. +# + +# If during a power failure, the remaining battery percentage +# (as reported by the UPS) is below or equal to BATTERYLEVEL, +# apcupsd will initiate a system shutdown. +BATTERYLEVEL 5 + +# If during a power failure, the remaining runtime in minutes +# (as calculated internally by the UPS) is below or equal to MINUTES, +# apcupsd, will initiate a system shutdown. +MINUTES 3 + +# If during a power failure, the UPS has run on batteries for TIMEOUT +# many seconds or longer, apcupsd will initiate a system shutdown. +# A value of 0 disables this timer. +# +# Note, if you have a Smart UPS, you will most likely want to disable +# this timer by setting it to zero. That way, you UPS will continue +# on batteries until either the % charge remaing drops to or below BATTERYLEVEL, +# or the remaining battery runtime drops to or below MINUTES. Of course, +# if you are testing, setting this to 60 causes a quick system shutdown +# if you pull the power plug. +# If you have an older dumb UPS, you will want to set this to less than +# the time you know you can run on batteries. +TIMEOUT 0 + +# Time in seconds between annoying users to signoff prior to +# system shutdown. 0 disables. +ANNOY 300 + +# Initial delay after power failure before warning users to get +# off the system. +ANNOYDELAY 60 + +# The condition which determines when users are prevented from +# logging in during a power failure. +# NOLOGON <string> [ disable | timeout | percent | minutes | always ] +NOLOGON disable + +# If KILLDELAY is non-zero, apcupsd will continue running after a +# shutdown has been requested, and after the specified time in +# seconds attempt to kill the power. This is for use on systems +# where apcupsd cannot regain control after a shutdown. +# KILLDELAY <seconds> 0 disables +KILLDELAY 0 + +# +# ==== Configuration statements for Network Information Server ==== +# + +# NETSERVER [ on | off ] on enables, off disables the network +# information server. If netstatus is on, a network information +# server process will be started for serving the STATUS and +# EVENT data over the network (used by CGI programs). +NETSERVER on + +# NISIP <dotted notation ip address> +# IP address on which NIS server will listen for incoming connections. +# This is useful if your server is multi-homed (has more than one +# network interface and IP address). Default value is 0.0.0.0 which +# means any incoming request will be serviced. Alternatively, you can +# configure this setting to any specific IP address of your server and +# NIS will listen for connections only on that interface. Use the +# loopback address (127.0.0.1) to accept connections only from the +# local machine. +NISIP 0.0.0.0 + +# NISPORT <port> default is 3551 as registered with the IANA +# port to use for sending STATUS and EVENTS data over the network. +# It is not used unless NETSERVER is on. If you change this port, +# you will need to change the corresponding value in the cgi directory +# and rebuild the cgi programs. +NISPORT 3551 + +# If you want the last few EVENTS to be available over the network +# by the network information server, you must define an EVENTSFILE. +EVENTSFILE /var/log/apcupsd.events + +# EVENTSFILEMAX <kilobytes> +# By default, the size of the EVENTSFILE will be not be allowed to exceed +# 10 kilobytes. When the file grows beyond this limit, older EVENTS will +# be removed from the beginning of the file (first in first out). The +# parameter EVENTSFILEMAX can be set to a different kilobyte value, or set +# to zero to allow the EVENTSFILE to grow without limit. +EVENTSFILEMAX 10 + +# +# ========== Configuration statements used if sharing ============= +# a UPS with more than one machine + +# +# Remaining items are for ShareUPS (APC expansion card) ONLY +# + +# UPSCLASS [ standalone | shareslave | sharemaster ] +# Normally standalone unless you share an UPS using an APC ShareUPS +# card. +UPSCLASS standalone + +# UPSMODE [ disable | share ] +# Normally disable unless you share an UPS using an APC ShareUPS card. +UPSMODE disable + +# +# ===== Configuration statements to control apcupsd system logging ======== +# + +# Time interval in seconds between writing the STATUS file; 0 disables +STATTIME 300 + +# Location of STATUS file (written to only if STATTIME is non-zero) +STATFILE /var/log/apcupsd.status + +# LOGSTATS [ on | off ] on enables, off disables +# Note! This generates a lot of output, so if +# you turn this on, be sure that the +# file defined in syslog.conf for LOG_NOTICE is a named pipe. +# You probably do not want this on. +LOGSTATS off + +# Time interval in seconds between writing the DATA records to +# the log file. 0 disables. +DATATIME 0 + +# FACILITY defines the logging facility (class) for logging to syslog. +# If not specified, it defaults to "daemon". This is useful +# if you want to separate the data logged by apcupsd from other +# programs. +#FACILITY DAEMON + +# +# ========== Configuration statements used in updating the UPS EPROM ========= +# + +# +# These statements are used only by apctest when choosing "Set EEPROM with conf +# file values" from the EEPROM menu. THESE STATEMENTS HAVE NO EFFECT ON APCUPSD. +# + +# UPS name, max 8 characters +#UPSNAME UPS_IDEN + +# Battery date - 8 characters +#BATTDATE mm/dd/yy + +# Sensitivity to line voltage quality (H cause faster transfer to batteries) +# SENSITIVITY H M L (default = H) +#SENSITIVITY H + +# UPS delay after power return (seconds) +# WAKEUP 000 060 180 300 (default = 0) +#WAKEUP 60 + +# UPS Grace period after request to power off (seconds) +# SLEEP 020 180 300 600 (default = 20) +#SLEEP 180 + +# Low line voltage causing transfer to batteries +# The permitted values depend on your model as defined by last letter +# of FIRMWARE or APCMODEL. Some representative values are: +# D 106 103 100 097 +# M 177 172 168 182 +# A 092 090 088 086 +# I 208 204 200 196 (default = 0 => not valid) +#LOTRANSFER 208 + +# High line voltage causing transfer to batteries +# The permitted values depend on your model as defined by last letter +# of FIRMWARE or APCMODEL. Some representative values are: +# D 127 130 133 136 +# M 229 234 239 224 +# A 108 110 112 114 +# I 253 257 261 265 (default = 0 => not valid) +#HITRANSFER 253 + +# Battery charge needed to restore power +# RETURNCHARGE 00 15 50 90 (default = 15) +#RETURNCHARGE 15 + +# Alarm delay +# 0 = zero delay after pwr fail, T = power fail + 30 sec, L = low battery, N = never +# BEEPSTATE 0 T L N (default = 0) +#BEEPSTATE T + +# Low battery warning delay in minutes +# LOWBATT 02 05 07 10 (default = 02) +#LOWBATT 2 + +# UPS Output voltage when running on batteries +# The permitted values depend on your model as defined by last letter +# of FIRMWARE or APCMODEL. Some representative values are: +# D 115 +# M 208 +# A 100 +# I 230 240 220 225 (default = 0 => not valid) +#OUTPUTVOLTS 230 + +# Self test interval in hours 336=2 weeks, 168=1 week, ON=at power on +# SELFTEST 336 168 ON OFF (default = 336) +#SELFTEST 336 diff --git a/abs/not_built/extra/apcupsd/run b/abs/not_built/extra/apcupsd/run new file mode 100644 index 0000000..bc5c22b --- /dev/null +++ b/abs/not_built/extra/apcupsd/run @@ -0,0 +1,4 @@ +#!/bin/sh +exec 2>&1 + stat_runit "Starting APC UPS Daemon" + exec /sbin/apcupsd -b -f /etc/apcupsd/apcupsd.conf |