diff options
Diffstat (limited to 'linhes/linhes-dev/LinHES9_iso/cust_skel/airootfs/etc/calamares/modules/preservefiles.conf')
-rw-r--r-- | linhes/linhes-dev/LinHES9_iso/cust_skel/airootfs/etc/calamares/modules/preservefiles.conf | 67 |
1 files changed, 67 insertions, 0 deletions
diff --git a/linhes/linhes-dev/LinHES9_iso/cust_skel/airootfs/etc/calamares/modules/preservefiles.conf b/linhes/linhes-dev/LinHES9_iso/cust_skel/airootfs/etc/calamares/modules/preservefiles.conf new file mode 100644 index 0000000..379d2fc --- /dev/null +++ b/linhes/linhes-dev/LinHES9_iso/cust_skel/airootfs/etc/calamares/modules/preservefiles.conf @@ -0,0 +1,67 @@ +# SPDX-FileCopyrightText: no +# SPDX-License-Identifier: CC0-1.0 +# +# Configuration for the preserve-files job +# +# The *files* key contains a list of files to preserve. Each element of +# the list should have one of these forms: +# +# - an absolute path (probably within the host system). This will be preserved +# as the same path within the target system (chroot). If, globally, +# *dontChroot* is true, then these items will be ignored (since the +# destination is the same as the source). +# - a map with a *dest* key. The *dest* value is a path interpreted in the +# target system (if the global *dontChroot* is true, then the host is the +# target as well). Relative paths are not recommended. There are two +# ways to select the source data for the file: +# - *from*, which must have one of the values, below; it is used to +# preserve files whose pathname is known to Calamares internally. +# - *src*, to refer to a path interpreted in the host system. Relative +# paths are not recommended, and are interpreted relative to where +# Calamares is being run. +# Exactly one of the two source keys (either *from* or *src*) must be set. +# +# Special values for the key *from* are: +# - *log*, for the complete log file (up to the moment the preservefiles +# module is run), +# - *config*, for a JSON dump of the contents of global storage. +# Note that this may contain sensitive information, and should be +# given restrictive permissions. +# +# A map with a *dest* key can have these additional fields: +# - *perm*, is a colon-separated tuple of <user>:<group>:<mode> +# where <mode> is in octal (e.g. 4777 for wide-open, 0400 for read-only +# by owner). If set, the file's ownership and permissions are set to +# those values within the target system; if not set, no permissions +# are changed. +# - *optional*, is a boolean; if this is set to `true` then failure to +# preserve the file will **not** be counted as a failure of the +# module, and installation will proceed. Set this for files that might +# not exist in the host system (e.g. nvidia configuration files that +# are created in some boot scenarios and not in others). +# +# The target path (*dest*) is modified as follows: +# - `@@ROOT@@` is replaced by the path to the target root (may be /). +# There is never any reason to use this, since the *dest* is already +# interpreted in the target system. +# - `@@USER@@` is replaced by the username entered by on the user +# page (may be empty, for instance if no user page is enabled) +# +# +# +files: + - from: log + dest: /var/log/Calamares.log + perm: root:root:644 + - from: config + dest: /var/log/Calamares-install.json + perm: root:root:644 +# - src: /var/log/nvidia.conf +# dest: /var/log/Calamares-nvidia.conf +# optional: true + +# The *perm* key contains a default value to apply to all files listed +# above that do not have a *perm* key of their own. If not set, +# root:root:0400 (highly restrictive) is used. +# +# perm: "root:root:0400" |