system-templates: updated lcdd files for new lcdproc

1 files changed, 581 insertions, 155 deletions

diff --git a/abs/core/system-templates/templates/LCD/Silverstone/LCDd.conf b/abs/core/system-templates/templates/LCD/Silverstone/LCDd.conf
index 2596c25..2fced90 100644
--- a/abs/core/system-templates/templates/LCD/Silverstone/LCDd.conf
+++ b/abs/core/system-templates/templates/LCD/Silverstone/LCDd.conf
@@ -1,7 +1,7 @@
 # LCDd.conf -- configuration file for the LCDproc server daemon LCDd
 #
 # This file contains the configuration for the LCDd server.
-# 
+#
 # The format is ini-file-like. It is divided into sections that start at
 # markers that look like [section]. Comments are all line-based comments,
 # and are lines that start with '#' or ';'.
@@ -10,7 +10,7 @@
 # a section called [menu]. Further each driver has a section which
 # defines how the driver acts.
 #
-# The drivers are activated by specifiying them in a driver= line in the
+# The drivers are activated by specifying them in a driver= line in the
 # server section, like:
 #
 #   Driver=curses
@@ -28,21 +28,29 @@
 ## Server section with all kinds of settings for the LCDd server ##
 [server]
 
+# Where can we find the driver modules ?
+# IMPORTANT: Make sure to change this setting to reflect your
+#            specific setup! Otherwise LCDd won't be able to find
+#            the driver modules and will thus not be able to
+#            function properly.
+# NOTE: Always place a slash as last character !
+DriverPath=/usr/lib/lcdproc/
+
 # Tells the server to load the given drivers. Multiple lines can be given.
 # The name of the driver is case sensitive and determines the section
 # where to look for further configuration options of the specific driver
 # as well as the name of the dynamic driver module to load at runtime.
-# The latter one can be changed by giving af File= directive in the
+# The latter one can be changed by giving a File= directive in the
 # driver specific section.
 #
 # The following drivers are supported:
-#   bayrad, CFontz, CFontz633, CFontzPacket, curses, CwLnx, EyeboxOne,
-#   g15, glcdlib, glk, hd44780, icp_a106, imon, IOWarrior, irman,
-#   joy, lb216,lcdm001, lcterm, lirc,MD8800, ms6931, mtc_s16209x,
-#   MtxOrb, NoritakeVFD, pyramid, sed1330, sed1520, serialVFD,
-#   sli, stv5730, svga, t6963, text, tyan, ula200, xosd
+#   bayrad, CFontz, CFontzPacket, curses, CwLnx, ea65,
+#   EyeboxOne, g15, glcd, glcdlib, glk, hd44780, icp_a106, imon, imonlcd,
+#   IOWarrior, irman, joy, lb216, lcdm001, lcterm, lirc, lis, MD8800,
+#   mdm166a, ms6931, mtc_s16209x, MtxOrb, mx5000, NoritakeVFD, picolcd,
+#   pyramid, sdeclcd, sed1330, sed1520, serialPOS, serialVFD, shuttleVFD, sli,
+#   stv5730, svga, t6963, text, tyan, ula200, vlsys_m428, xosd
 Driver=imon
-#Driver=curses
 
 # Tells the driver to bind to the given interface
 Bind=127.0.0.1
@@ -53,72 +61,80 @@ Port=13666
 # Sets the reporting level; defaults to 2 (warnings and errors only).
 #ReportLevel=3
 
-# Should we report to syslog instead of stderr ? Default: no
+# Should we report to syslog instead of stderr ? [default: no; legal: yes, no]
 #ReportToSyslog=yes
 
+# User to run as.  LCDd will drop its root privileges, if any,
+# and run as this user instead.
+User=nobody
+
+# The server will stay in the foreground if set to true.
+#Foreground=no
+
+# Hello message: each entry represents a display line; default: builtin
+Hello="LinHES"
+#Hello="  Welcome to"
+#Hello="   LCDproc!"
+
+# GoodBye message: each entry represents a display line; default: builtin
+GoodBye=""
+#GoodBye="Thanks for using"
+#GoodBye="   LCDproc!"
+
 # Sets the default time in seconds to displays a screen.
-WaitTime=5
+WaitTime=10
 
-# User to run as.  LCDd will drop its root priviledges,
-# if any, and run as this user instead.
-User=nobody
+# If set to no, LCDd will start with screen rotation disabled. This has the
+# same effect as if the ToggleRotateKey had been pressed. Rotation will start
+# if the ToggleRotateKey is pressed. Note that this setting does not turn off
+# priority sorting of screens. [default: on; legal: on, off]
+#AutoRotate=no
 
 # If yes, the the serverscreen will be rotated as a usual info screen. If no,
 # it will be a background screen, only visible when no other screens are
-# active.
-#ServerScreen=no
+# active. The special value 'blank' is similar to no, but only a blank screen
+# is displayed. [default: on; legal: on, off, blank]
+ServerScreen=blank
 
-# The server will stay in the foreground if set to true.
-#Foreground=no
+# Set master backlight setting. If set to 'open' a client may control the
+# backlight for its own screens (only). [default: open; legal: off, open, on]
+#Backlight=open
 
-# Where can we find the driver modules ?
-# IMPORTANT: Make sure to change this setting to reflect your
-#            specific setup! Otherwise LCDd won't be able to find
-#            the driver modules and will thus not be able to
-#            function properly.
-# NOTE: Always place a slash as last character !
-DriverPath=/usr/lib/lcdproc/
+# Set master heartbeat setting. If set to 'open' a client may control the
+# heartbeat for its own screens (only). [default: open; legal: off, open, on]
+#Heartbeat=open
+
+# set title scrolling speed [default: 10; legal: 0-10]
+#TitleSpeed=10
 
 # The "...Key=" lines define what the server does with keypresses that
-# don't go to any client.
-# These are the defaults:
+# don't go to any client. The ToggleRotateKey stops rotation of screens, while
+# the PrevScreenKey and NextScreenKey go back / forward one screen (even if
+# rotation is disabled.
+# Assign the key string returned by the driver to the ...Key setting. These
+# are the defaults:
 ToggleRotateKey=Enter
 PrevScreenKey=Left
 NextScreenKey=Right
 #ScrollUpKey=Up
 #ScrollDownKey=Down
 
-# If you have only 4 keys, you can choose to use this:
-#ToggleRotateKey=Enter
-#PrevScreenKey=Up
-#NextScreenKey=Down
-
-# If you have only 3 keys, you can choose to use this:
-#ToggleRotateKey=Enter
-#PrevScreenKey=Up
-
-
 
 ## The menu section. The menu is an internal LCDproc client. ##
 [menu]
 # You can configure what keys the menu should use. Note that the MenuKey
 # will be reserved exclusively, the others work in shared mode.
 
-# The following works excellent with 4 keys or more.
+# Up to six keys are supported. The MenuKey (to enter and exit the menu), the
+# EnterKey (to select values) and at least one movement keys are required.
+# These are the default key assignments:
 MenuKey=Escape
 EnterKey=Enter
 UpKey=Up
 DownKey=Down
-# If you have 6 keys you may define these as well
 #LeftKey=Left
 #RightKey=Right
 
-# If you have only 3 keys, you could use something like this:
-#MenuKey=Escape
-#EnterKey=Enter
-#DownKey=Down
-
-
 
 ### Driver sections are below this line, in alphabetical order  ###
 
@@ -143,13 +159,14 @@ Device=/dev/ttyS0
 Size=20x4
 # Set the initial contrast [default: 560; legal: 0 - 1000]
 Contrast=350
-# Set the initial brightness [default: 255; legal: 0 - 255]
-Brightness=255
-# Set the initial off-brightness [default: 0; legal: 0 - 255]
+# Set the initial brightness [default: 1000; legal: 0 - 1000]
+Brightness=1000
+# Set the initial off-brightness [default: 0; legal: 0 - 1000]
 # This value is used when the display is normally
 # switched off in case LCDd is inactive
 OffBrightness=0
-# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200 or 115200]
+# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200,
+# 115200]
 Speed=9600
 # Set the firmware version (New means >= 2.0) [default: no; legal: yes, no]
 NewFirmware=no
@@ -159,57 +176,45 @@ Reboot=no
 
 
 
-## CrystalFontz633 driver (for CF633 only) ##
-[CFontz633]
+## CrystalFontz packet driver (for CFA533, CFA631, CFA633 & CFA635) ##
+[CFontzPacket]
+
+# Select the LCD model [default: 633; legal: 533, 631, 633, 635]
+Model=633
 
 # Select the output device to use [default: /dev/lcd]
-Device=/dev/ttyS0
-# Select the LCD type (size) [default: 16x2]
-Size=16x2
+Device=/dev/ttyUSB0
+
 # Set the initial contrast [default: 560; legal: 0 - 1000]
 Contrast=350
+
 # Set the initial brightness [default: 1000; legal: 0 - 1000]
 Brightness=1000
+
 # Set the initial off-brightness [default: 0; legal: 0 - 1000]
 # This value is used when the display is normally
 # switched off in case LCDd is inactive
 OffBrightness=50
-# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200]
-Speed=19200
-# Set the firmware version (New means >= 2.0) [default: no; legal: yes, no]
-# Currently this flag is not in use, there is no such thing as NewFirmware. ;=)
-#NewFirmware=no
-# Reinitialize the LCD's BIOS [default: no; legal: yes, no]
-# I want to reboot the LCD to make sure we start from a known state
+
+# Reinitialize the LCD's BIOS on driver start. [default: no; legal: yes, no]
 Reboot=yes
 
+# Enable the USB flag if the device is connected to an USB port. For
+# serial ports leave it disabled. [default: no; legal: yes, no]
+#USB=yes
 
+# Very old 633 firmware versions do not support partial screen updates using
+# 'Send Data to LCD' command (31). For those devices it may be necessary to
+# enable this flag. [default: no; legal: yes, no]
+#OldFirmware=yes
 
-## CrystalFontz packet driver (for CF631, CF633 & CF635) ##
-[CFontzPacket]
+# Override the LCD size known for the selected model. Usually setting this
+# value should not be necessary.
+#Size=20x4
 
-# Select the LCD model [default: 633; legal: 631, 633, 635]
-Model=635
-# Select the output device to use [default: /dev/lcd]
-Device=/dev/ttyUSB0
-# Select the LCD size [default: depending on model: 635: 20x4, 631: 20x2, 633: 16x2]
-Size=20x4
-# Set the initial contrast [default: 560; legal: 0 - 1000]
-Contrast=350
-# Set the initial brightness [default: 1000; legal: 0 - 1000]
-Brightness=1000
-# Set the initial off-brightness [default: 0; legal: 0 - 1000]
-# This value is used when the display is normally
-# switched off in case LCDd is inactive
-OffBrightness=50
-# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200]
-Speed=115200
-# Set the firmware version (New means >= 2.0) [default: no; legal: yes, no]
-# Currently this flag is not in use, there is no such thing as NewFirmware. ;=)
-#NewFirmware=no
-# Reinitialize the LCD's BIOS [default: no; legal: yes, no]
-# I want to reboot the LCD to make sure we start from a known state
-Reboot=yes
+# Override the default communication speed known for the selected model.
+# Default value depends on model [legal: 19200, 115200]
+#Speed=115200
 
 
 
@@ -232,20 +237,27 @@ Size=20x4
 TopLeftX=7
 TopLeftY=7
 
-# use ASC symbols for icons & bars [default: no; legal, yes, no]
+# use ASC symbols for icons & bars [default: no; legal: yes, no]
 UseACS=no
 
+# draw Border [default: yes; legal: yes, no]
+DrawBorder=yes
+
 
 
 ## Cwlinux driver ##
 [CwLnx]
 
-# Select the LCD model [default: 12232; legal: 12232, 1602]
+# Select the LCD model [default: 12232; legal: 12232, 12832, 1602]
 Model=12232
+
 # Select the output device to use [default: /dev/lcd]
 Device=/dev/ttyUSB0
 
-# Select the LCD size [default: depending on model: 12232: 20x4, 1602: 16x2]
+# Select the LCD size. Default depends on model:
+# 12232: 20x4
+# 12832: 21x4
+# 1602: 16x2
 Size=20x4
 
 # Set the communication speed [default: 19200; legal: 9600, 19200]
@@ -274,12 +286,29 @@ Keypad=yes
 # KeyMap_E=Enter
 # KeyMap_F=Escape
 
-# keypad_test_mode permits to test keypad assignement
+# keypad_test_mode permits one to test keypad assignment
 # Default value is no
 #keypad_test_mode=yes
 
 
 
+## ea65 driver for the display in AOpen XC Cube AV EA65 media barebones ##
+[ea65]
+
+# Device is fixed /dev/ttyS1
+# Width and Height are fixed 9x1
+
+# As the VFD is self luminescent we don't have a backlight
+# But we can use the backlight functions to control the front LEDs
+# Brightness 0 to 299 -> LEDs off
+# Brightness 300 to 699 -> LEDs half bright
+# Brightness 700 to 1000 -> LEDs full bright
+Brightness=500
+# OffBrightness is the the value used for the 'backlight off' state
+OffBrightness=0
+
+
+
 ## EyeboxOne driver ##
 [EyeboxOne]
 
@@ -314,12 +343,98 @@ EscapeKey=P
 keypad_test_mode=no
 
 
+
 ## g15 driver for Logitech G15 Keyboard LCDs ##
 [g15]
 
 # Display size (currently unused)
 size=20x5
 
+
+
+## glcd generic graphical display driver
+[glcd]
+# Select what type of connection. See documentation for types.
+ConnectionType=t6963
+
+# Width and height of the display in pixel. The supported sizes may depend on
+# the ConnectionType. [default: 128x64; legal: 1x1 - 640x480]
+#Size=128x64
+
+# Width and height of a character cell in pixels. This value is only used if
+# the driver has been compiled with FreeType and it is enabled. Otherwise the
+# default 6x8 cell is used.
+#CellSize=12x16
+
+# If LCDproc has been compiled with FreeType 2 support this option can be used
+# to turn if off intentionally. [default: yes; legal: yes, no]
+#useFT2=no
+
+# Path to font file to use for FreeType rendering. This font must be monospace
+# and should contain some special Unicode characters like arrows (Andale Mono
+# is recommended and can be fetched at http://corefonts.sf.net).
+#normal_font=/usr/local/lib/X11/fonts/TTF/andalemo.ttf
+
+# Some fonts miss the Unicode characters used to represent icons. In this case
+# the built-in 5x8 font can used if this option is turned off. [default: yes;
+# legal: yes, no]
+#fontHasIcons=no
+
+# Set the initial contrast if supported by connection type.
+# [default: 600; legal: 0 - 1000]
+#Contrast=600
+
+# Set brightness of the backlight if the backlight is switched 'on'.
+# [default: 800; legal: 0 - 1000]
+#Brightness=1000
+
+# Set brightness of the backlight if the backlight is switched 'off'. Set this
+# to zero to completely turn off the backlight. [default: 100; legal: 0 - 1000]
+#OffBrightness=0
+
+# Time (ms) from first key report to first repeat. Set to 0 to disable repeated
+# key reports. [default: 500; legal: 0 - 3000]
+#KeyRepeatDelay=500
+
+# Time (ms) between repeated key reports. Ignored if KeyRepeatDelay is disabled
+# (set to zero). [default: 300; legal: 0 - 3000]
+#KeyRepeatInterval=300
+
+# Assign key strings to keys. There may be up to 16 keys numbered 'A' to 'Z'.
+# By default keys 'A' to 'F' are assigned Up, Down, Left, Right, Enter, Escape.
+KeyMap_A=Up
+KeyMap_B=Down
+KeyMap_C=Enter
+KeyMap_D=Escape
+
+# t6963: Parallel port to use [default: 0x378; legal: 0x200 - 0x400]
+#Port=0x378
+
+# t6963: Use LPT port in bi-directional mode. This should work on most LPT port
+# and is required for proper timing! [default: yes; legal: yes, no]
+#bidirectional=yes
+
+# t6963: Insert additional delays into reads / writes. [default: no;
+# legal: yes, no]
+#delayBus=no
+
+# serdisplib: Name of the underlying serdisplib driver, e.g. ctinclud. See
+# serdisplib documentation for details.
+serdisp_name=t6963
+
+# serdisplib: The display device to use, e.g. serraw:/dev/ttyS0,
+# parport:/dev/parport0 or USB:07c0/1501.
+serdisp_device=/dev/ppi0
+
+# serdisplib: Options string to pass to serdisplib during initialization. Use
+# this to set any display related options (e.g. wiring). The display size is
+# always set based on the Size configured above! By default, no options are
+# set.
+# Important: The value must be quoted as it contains equal signs!
+#serdisp_options="INVERT=1"
+
+
+
 ## glcdlib meta driver for graphical LCDs ##
 [glcdlib]
 
@@ -330,40 +445,39 @@ size=20x5
 Driver=noritake800
 
 # no=use graphlcd bitmap fonts (they have only one size / font file)
-# yes=use fonts supported by FreeType2 (needs Freetype2 support in libglcdprocdriver and its dependants)
+# yes=use fonts supported by FreeType2 (needs Freetype2 support in
+# libglcdprocdriver and its dependants)
 UseFT2=yes
 
 # text resolution in fixed width characters [default: 16x4]
-# (if it won't fit according to available physical pixel resolutioni
-# and the minimum available font face size in pixels, then 
+# (if it won't fit according to available physical pixel resolution
+# and the minimum available font face size in pixels, then
 # 'DebugBorder' will automatically be turned on)
 TextResolution=20x4
 
 # path to font file to use
 FontFile=/usr/share/fonts/corefonts/courbd.ttf
 
-
 ## these only apply if UseFT2=yes:
 
 # character encoding to use
 CharEncoding=iso8859-2
 
-# minumum size in pixels in which fonts should be rendered
+# minimum size in pixels in which fonts should be rendered
 MinFontFaceSize=7x12
 
-
 ## optional:
-Brightness=50			# Brightness (in %) if applicable
-Contrast=50			# Contrast (in %) if applicable
-Backlight=no			# Backlight if applicable
-UpsideDown=no			# flip image upside down
-Invert=no			# invert light/dark pixels
-ShowDebugFrame=no		# turns on/off 1 pixel thick debugging
-				# border whithin the usable text area,
-				# for setting up TextResolution and
-				# MinFontFaceSize (if using FT2);
-ShowBigBorder=no		# border around the unused area
-ShowThinBorder=yes		# border around the unused area
+Brightness=50                   # Brightness (in %) if applicable
+Contrast=50                     # Contrast (in %) if applicable
+Backlight=no                    # Backlight if applicable
+UpsideDown=no                   # flip image upside down
+Invert=no                       # invert light/dark pixels
+ShowDebugFrame=no               # turns on/off 1 pixel thick debugging
+                                # border within the usable text area,
+                                # for setting up TextResolution and
+                                # MinFontFaceSize (if using FT2);
+ShowBigBorder=no                # border around the unused area
+ShowThinBorder=yes              # border around the unused area
 PixelShiftX=0
 PixelShiftY=2
 
@@ -389,10 +503,10 @@ Speed=19200
 # Select what type of connection. See documentation for types.
 ConnectionType=4bit
 
-# Port where the LPT is. Usual values are 0x278, 0x378 and 0x3BC
+# Port where the LPT is. Usual value are: 0x278, 0x378 and 0x3BC
 Port=0x378
 
-# Device of the serial interface (default is /dev/lcd)
+# Device of the serial interface [default: /dev/lcd]
 Device=/dev/ttyS0
 
 # Bitrate of the serial port (0 for interface default)
@@ -402,8 +516,18 @@ Speed=0
 # You may also need to configure the keypad layout further on in this file.
 Keypad=no
 
-# set the initial contrast (for bwctusb only) [default: 0; legal: 0 - 1000]
-Contrast=0
+# Set the initial contrast (bwctusb, lcd2usb, and usb4all)
+# [default: 800; legal: 0 - 1000]
+#Contrast=0
+
+# Set brightness of the backlight (lcd2usb and usb4all):
+# Brightness is the brightness while the backlight is set to 'on'.
+# [default: 800; legal: 0 - 1000]
+#Brightness=1000
+
+# OffBrightness is the brightness while the backlight is set to 'off'.
+# [default: 300; legal: 0 - 1000]
+#OffBrightness=0
 
 # If you have a switchable backlight.
 Backlight=no
@@ -412,9 +536,9 @@ Backlight=no
 # be able to control it with the lcdproc OUTPUT command
 OutputPort=no
 
-# Specifies if the last line is pixel addressable or it controls an
-# underline effect. [default: true (= pixel addressable); legal: yes, no]
-#Lastline=true
+# Specifies if the last line is pixel addressable (yes) or it controls an
+# underline effect (no). [default: yes; legal: yes, no]
+#Lastline=yes
 
 # Specifies the size of the LCD.
 # In case of multiple combined displays, this should be the total size.
@@ -424,20 +548,36 @@ Size=20x4
 # Vspan=2,2 means both displays have 2 lines.
 #vspan=2,2
 
-# If you have an HD66712, a KS0073 or an other 'almost HD44780-compatible',
+# If you have an HD66712, a KS0073 or another 'almost HD44780-compatible',
 # set this flag to get into extended mode (4-line linear).
-# This flag is NOT the old obsolete Extended option.
 #ExtendedMode=yes
 
+# In extended mode, on some controllers like the ST7036 (in 3 line mode)
+# the next line in DDRAM won't start 0x20 higher. [default: 0x20]
+#LineAddress=0x10
+
 # Character map to to map ISO-8859-1 to the LCD's character set
-# [default: hd44780_default; legal: hd44780_default, ea_ks0073 ]
-Charmap=hd44780_default
+# [default: hd44780_default; legal: hd44780_default, hd44780_euro, ea_ks0073,
+# sed1278f_0b, hd44780_koi8_r, hd44780_cp1251, hd44780_8859_5, upd16314 ]
+# (hd44780_koi8_r, hd44780_cp1251, hd44780_8859_5 and upd16314 are possible if
+# compiled with additional charmaps)
+CharMap=hd44780_default
 
 # If your display is slow and cannot keep up with the flow of data from
 # LCDd, garbage can appear on the LCDd. Set this delay factor to 2 or 4
 # to increase the delays. Default: 1.
 #DelayMult=2
 
+# Some displays (e.g. vdr-wakeup) need a message from the driver to that it
+# is still alive. When set to a value bigger then null the character in the
+# upper left corner is updated every <KeepAliveDisplay> seconds. Default: 0.
+#KeepAliveDisplay=0
+
+# If you experience occasional garbage on your display you can use this
+# option as workaround. If set to a value bigger than null it forces a
+# full screen refresh <RefreshDiplay> seconds. Default: 0.
+#RefreshDisplay=5
+
 # You can reduce the inserted delays by setting this to false.
 # On fast PCs it is possible your LCD does not respond correctly.
 # Default: true.
@@ -468,13 +608,17 @@ Device=/dev/ttyS1
 # display dimensions
 Size=20x4
 
-# serial number [exactly as listed by usbview]
+# serial number. Must be exactly as listed by usbview
 # (if not given, the 1st IOWarrior found gets used)
 #SerialNumber=00000674
 
-# Specifies if the last line is pixel addressable or it controls an
-# underline effect. [default: true (= pixel addressable); legal: yes, no]
-#Lastline=true
+# If you have an HD66712, a KS0073 or another 'almost HD44780-compatible',
+# set this flag to get into extended mode (4-line linear).
+#ExtendedMode=yes
+
+# Specifies if the last line is pixel addressable (yes) or it controls an
+# underline effect (no). [default: yes; legal: yes, no]
+#Lastline=yes
 
 
 
@@ -487,11 +631,49 @@ Device=/dev/lcd0
 # display dimensions
 Size=16x2
 
+# Character map to to map ISO-8859-1 to the displays character set.
+# [default: none; legal: none, hd44780_euro, upd16314, hd44780_koi8_r,
+# hd44780_cp1251, hd44780_8859_5 ] (upd16314, hd44780_koi8_r,
+# hd44780_cp1251, hd44780_8859_5 are possible if compiled with additional
+# charmaps)
+CharMap=hd44780_euro
+
+## Soundgraph iMON LCD ##
+[imonlcd]
+# Specify which iMon protocol should be used
+# [legal: 0, 1; default: 0]
+# Choose 0 for 15c2:ffdc device,
+# Choose 1 for 15c2:0038 device
+Protocol=0
+
+# Set the exit behavior [legal: 0-2; default: 1]
+# 0 means leave shutdown message,
+# 1 means show the big clock,
+# 2 means blank device
+#OnExit=2
+
+# Select the output device to use [default: /dev/lcd0]
+Device=/dev/lcd0
+
+# Select the displays contrast [default: 200; legal: 0-1000]
+Contrast=200
+
+# Specify the size of the display in pixels [default: 96x16]
+#Size=96x16
+
+# Set the backlight state [default: on; legal: on, off]
+#Backlight=on
+
+# Set the disc mode [legal: 0,1; default: 0]
+# 0 => spin the "slim" disc - two disc segments,
+# 1 => their complement spinning;
+#DiscMode=0
+
 
 
 ## IrMan driver ##
 [IrMan]
-#if in trouble with IrMan, try Lirc emulator for IrMan
+# in case of trouble with IrMan, try the Lirc emulator for IrMan
 
 # Select the input device to use
 #Device=/dev/irman
@@ -501,6 +683,20 @@ Size=16x2
 
 
 
+## IRtrans driver ##
+[irtrans]
+
+# Does the device have a backlight? [default: no; legal: yes, no]
+#Backlight=no
+
+# IRTrans device to connect to [default: localhost]
+#Hostname=localhost
+
+# display dimensions
+Size=16x2
+
+
+
 ## Joystick driver ##
 [joy]
 
@@ -577,6 +773,30 @@ Size=16x2
 
 
 
+## LIS MCE 2005 driver ##
+[lis]
+
+# Set the initial brightness [default: 1000; legal: 0 - 1000]
+# 0-250 = 25%, 251-500 = 50%, 501-750 = 75%, 751-1000 = 100%
+#Brightness=1000
+
+# Columns by lines [default: 20x2]
+#Size=20x2
+
+# USB Vendor ID [default: 0x0403]
+# Change only if testing a compatible device.
+#VendorID=0x0403
+
+# USB Product ID [default: 0x6001]
+# Change only if testing a compatible device.
+#ProductID=0x6001
+
+# Specifies if the last line is pixel addressable (yes) or it only controls an
+# underline effect (no). [default: yes; legal: yes, no]
+#Lastline=yes
+
+
+
 ##The driver for the VFD of the Medion MD8800 PC ##
 [MD8800]
 # device to use [default: /dev/ttyS1]
@@ -594,6 +814,18 @@ OffBrightness=50
 
 
 
+## Futuba MDM166A Display
+[mdm166a]
+# Show self-running clock after LCDd shutdown
+# Possible values: [default: no; legal: no, small, big]
+Clock=big
+# Dim display, no dimming gives full brightness [default: no, legal: yes, no]
+Dimming=no
+# Dim display in case LCDd is inactive [default: no, legal: yes, no]
+OffDimming=yes
+
+
+
 ## MSI MS-6931 driver for displays in 1HU servers ##
 [ms6931]
 
@@ -628,23 +860,30 @@ Device=/dev/ttyS0
 # Set the display size [default: 20x4]
 Size=20x4
 
-# Switch on the backlight? [default: yes]
-# NOTE: The driver will ignore this if the display is a vfd or vkd
-#       as they crash if the backlight is turned off
-Backlight=yes
+# Set the display type [default: lcd; legal: lcd, lkd, vfd, vkd]
+Type=lkd
 
 # Set the initial contrast [default: 480]
 # NOTE: The driver will ignore this if the display
 #       is a vfd or vkd as they don't have this feature
-Contrast=800
+Contrast=480
+
+# Some old displays do not have an adjustable backlight but only can
+# switch the backlight on/off. If you experience randomly appearing block
+# characters, try setting this to false. [default: yes; legal: yes, no]
+hasAdjustableBacklight=no
+
+# Set the initial brightness [default: 1000; legal: 0 - 1000]
+Brightness=1000
+# Set the initial off-brightness [default: 0; legal: 0 - 1000]
+# This value is used when the display is normally
+# switched off in case LCDd is inactive
+OffBrightness=0
 
 # Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200]
 Speed=19200
 
-# Set the display type [default: lcd; legal: lcd, lkd, vfd, vkd]
-Type=lkd
-
-# The following table translates from MtxOrb key letters to logical key namess.
+# The following table translates from MtxOrb key letters to logical key names.
 # By default no keys are mapped, meaning the keypad is not used at all.
 #KeyMap_A=Left
 #KeyMap_B=Right
@@ -663,22 +902,107 @@ keypad_test_mode=no
 
 
 
+## mx5000 driver for LCD display on the Logitech MX5000 keyboard ##
+[mx5000]
+
+# Select the output device to use [default: /dev/hiddev0]
+Device = /dev/hiddev0
+# Time to wait in ms after the refresh screen has been sent [default: 1000]
+WaitAfterRefresh = 1000
+
+
+
 ## Noritake VFD driver ##
 [NoritakeVFD]
-# device where the VFD is. Usual values are /dev/ttyS0 and /dev/ttyS1 [default: /dev/lcd]
+# device where the VFD is. Usual values are /dev/ttyS0 and /dev/ttyS1
+# [default: /dev/lcd]
 Device=/dev/ttyS0
-
 # Specifies the size of the LCD.
 Size=20x4
-
-# set the brightness
-Brightness=255
-
+# Set the initial brightness [default: 1000; legal: 0 - 1000]
+Brightness=1000
+# Set the initial off-brightness [default: 0; legal: 0 - 1000]
+# This value is used when the display is normally
+# switched off in case LCDd is inactive
+OffBrightness=50
 # set the serial port speed [default: 9600, legal: 1200, 2400, 9600, 19200, 115200]
 Speed=9600
+# Set serial data parity [default: 0; legal: 0-2 ]
+# Meaning: 0(=none), 1(=odd), 2(=even)
+Parity=0
+# re-initialize the VFD [default: no; legal: yes, no]
+Reboot=no
+
 
-# re-initialize VFD ?
-#Reboot=yes
+
+## Mini-box.com picoLCD (usblcd) driver ##
+[picolcd]
+
+# KeyTimeout is only used if the picoLCD driver is built with libusb-0.1. When
+# built with libusb-1.0 key and IR data is input asynchronously so there is no
+# need to wait for the USB data.
+# KeyTimeout is the time in ms that LCDd spends waiting for a key press before
+# cycling through other duties.  Higher values make LCDd use less CPU time and
+# make key presses more detectable.  Lower values make LCDd more responsive
+# but a little prone to missing key presses.  500 (.5 second) is the default
+# and a balanced value. [default: 500; legal: 0 - 1000]
+KeyTimeout=500
+
+# Key auto repeat is only available if the picoLCD driver is built with
+# libusb-1.0. Use KeyRepeatDelay and KeyRepeatInterval to configure key auto
+# repeat.
+#
+# Key auto repeat delay (time in ms from first key report to first repeat). Use
+# zero to disable auto repeat. [default: 300; legal: 0 - 3000]
+KeyRepeatDelay=300
+
+# Key auto repeat interval (time in ms between repeat reports). Only used if
+# KeyRepeatDelay is not zero. [default: 200; legal: 0 - 3000]
+KeyRepeatInterval=200
+
+# Sets the initial state of the backlight upon start-up.
+# [default: on; legal: on, off]
+#Backlight=on
+
+# Set the initial brightness [default: 1000; legal: 0 - 1000]. Works only
+# with the 20x4 device
+Brightness=1000
+
+# Set the brightness while the backlight is 'off' [default: 0; legal: 0 - 1000].
+# Works only with the 20x4 device.
+#OffBrightness=0
+
+# Set the initial contrast [default: 1000; legal: 0 - 1000]
+Contrast=1000
+
+# Link the key lights to the backlight? [default: on; legal: on, off]
+#LinkLights=off
+
+# Light the keys? [default: on; legal: on, off]
+Keylights=on
+
+# If Keylights is on, the you can unlight specific keys below:
+# Key0 is the directional pad.  Key1 - Key5 correspond to the F1 - F5 keys.
+# There is no LED for the +/- keys.  This is a handy way to indicate to users
+# which keys are disabled.  [default: on; legal: on, off]
+Key0Light=on
+Key1Light=on
+Key2Light=on
+Key3Light=on
+Key4Light=on
+Key5Light=on
+
+# Host name or IP address of the LIRC instance that is to receive IR codes
+# If not set, or set to an empty value, IR support is disabled.
+#LircHost=127.0.0.1
+
+# UDP port on which LIRC is listening [default: 8765; legal: 1 - 65535]
+LircPort=8765
+
+# Threshold in jiffies of synthesized gap that triggers flushing the IR data
+# to lirc [default: 100 ; max: 32767 ]
+# 100 means 6.1ms. legal: 16 - 32767; Use 0 to disable.
+LircFlushThreshold=100
 
 
 
@@ -690,16 +1014,28 @@ Device=/dev/ttyUSB0
 
 
 
+## SDEC driver for Watchguard Firebox ##
+[sdeclcd]
+# No options
+
+
+
 ## Seiko Epson 1330 driver ##
 [sed1330]
 
 # Port where the LPT is. Common values are 0x278, 0x378 and 0x3BC
 Port=0x378
 
-# Type of LCD module (legal: G321D, G121C, G242C, G191D, G2446)
-# Note: G321D is the only one that is tested currently.
+# Type of LCD module (legal: G321D, G121C, G242C, G191D, G2446, SP14Q002)
+# Note: Currently only tested with G321D & SP14Q002.
 Type=G321D
 
+# Width x Height of a character cell in pixels [legal: 6x7 - 8x16; default: 6x10]
+CellSize=6x10
+
+# Select what type of connection [legal: classic, bitshaker; default: classic]
+ConnectionType=classic
+
 
 
 ## Seiko Epson 1520 driver ##
@@ -708,6 +1044,39 @@ Type=G321D
 # Port where the LPT is. Usual values are 0x278, 0x378 and 0x3BC
 Port=0x378
 
+# Select the interface type (wiring) for the display. Supported values are
+# 68 for 68-style connection (RESET level high) and 80 for 80-style connection
+# (RESET level low). [legal: 68, 80; default: 80]
+InterfaceType=80
+
+# On fast machines it may be necessary to slow down transfer to the display.
+# If this value is set to zero, delay is disabled. Any value greater than
+# zero slows down each write by one microsecond. [legal: 0-1000; default: 1]
+DelayMult=0
+
+# The original wiring used an inverter to drive the control lines. If you do
+# not use an inverter set haveInverter to no. [default: yes; legal: yes, no]
+haveInverter=no
+
+
+
+## serial POS display driver ##
+[serialPOS]
+
+# Device to use in serial mode [default: /dev/lcd]
+Device=/dev/lcd
+
+# Specifies the size of the display in characters. [default: 16x2]
+Size=16x2
+
+# Set the communication protocol to use with the POS display.
+# [default: AEDEX; legal: IEE, Epson, Emax, IBM, LogicControls, Ultimate]
+Type=AEDEX
+
+# communication baud rate with the display [default: 9600; legal: 1200, 2400,
+# 19200, 115200]
+Speed=9600
+
 
 
 ## Serial VFD driver ##
@@ -719,18 +1088,29 @@ Port=0x378
 # 1 KD Rev 2.1.
 # 2 Noritake VFDs (*).
 # 3 Futaba VFDs
-# (* most should work, not testet yet.)
+# 4 IEE S03601-95B
+# 5 IEE S03601-96-080 (*)
+# 6 Futaba NA202SD08FA (allmost IEE compatible)
+# 7 Samsung 20S207DA4 and 20S207DA6
+# 8 Nixdorf BA6x / VT100
+# (* most should work, not tested yet.)
 Type=0
 
-# "no" if display connected serial, "yes" if connected parallel. [default: no(=serial)]
+# "no" if display connected serial, "yes" if connected parallel. [default: no]
+# I.e. serial by default
 use_parallel=no
 
-# Number of Custom-Characters [default: displaytype dependent]
+# Number of Custom-Characters. default is display type dependent
 #Custom-Characters=0
 
-# Portaddress where the LPT is. Used in parallelmode only. Usual values are 0x278, 0x378 and 0x3BC
+# Portaddress where the LPT is. Used in parallel mode only. Usual values are
+# 0x278, 0x378 and 0x3BC.
 Port=0x378
 
+# Set parallel port timing delay (us). Used in parallel mode only.
+# [default: 2; legal: 0 - 255]
+#PortWait=2
+
 # Device to use in serial mode. Usual values are /dev/ttyS0 and /dev/ttyS1
 Device=/dev/ttyS1
 
@@ -754,6 +1134,12 @@ Speed=9600
 
 
 
+## shuttleVFD driver ##
+[shuttleVFD]
+# No options
+
+
+
 ## stv5730 driver ##
 [stv5730]
 
@@ -761,11 +1147,35 @@ Speed=9600
 Port=0x378
 
 
+[SureElec]
+
+# Port the device is connected to  (by default first USB serial port)
+Device=/dev/ttyUSB0
+
+# Edition level of the device (can be 1, 2 or 3) [default: 2]
+#Edition=1
+
+# set display size
+# Note: The size can be obtained directly from device for edition 2 & 3.
+#Size=16x2
+
+# Set the initial contrast [default: 480; legal: 0 - 1000]
+#Contrast=200
+
+# Set the initial brightness [default: 480; legal: 1 - 1000]
+#Brightness=480
+
+# Set the initial off-brightness [default: 100; legal: 1 - 1000]
+# This value is used when the display is normally
+# switched off in case LCDd is inactive
+#OffBrightness=100
+
 
 ## SVGAlib driver ##
 [svga]
 
-# svgalib mode to use [default: G320x240x256; legal: supported svgalib modes]
+# svgalib mode to use [default: G320x240x256 ]
+# legal values are supported svgalib modes
 #Mode=G640x480x256
 
 # set display size [default: 20x4]
@@ -795,17 +1205,21 @@ Size=20x4
 ## Toshiba T6963 driver ##
 [t6963]
 
-# set display size [default: 20x6]
-Size=20x6
+# set display size in pixels [default: 128x64]
+Size=128x64
 
 # port to use [default: 0x378; legal: 0x200 - 0x400]
 Port=0x378
 
-# Is ECP mode on? [default: yes; legal: yes, no]
-#ECPlpt=yes
+# Use LPT port in bi-directional mode. This should work on most LPT port and
+# is required for proper timing! [default: yes; legal: yes, no]
+#bidirectional=yes
 
-# Use graphics? [default: no; legal: yes, no]
-#graphic=no
+# Insert additional delays into reads / writes. [default: no; legal: yes, no]
+#delayBus=no
+
+# Clear graphic memory on start-up. [default: no; legal: yes, no]
+#ClearGraphic=no
 
 
 
@@ -852,18 +1266,30 @@ Size=20x4
 # Select the output device to use [default: /dev/lcd]
 Device=/dev/lcd
 
-# Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200, 38400, 57600, 115200]
+# Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200,
+# 38400, 57600, 115200]
 Speed=19200
 
 
 
+## vlsys_m428 for VFD/IR combination in Moneual MonCaso 320 ##
+[vlsys_m428]
+
+# Select the output device to use [default: /dev/ttyUSB0]
+#Device=/dev/ttyUSB0
+
+
+
 ## OnScreen Display using libxosd ##
 [xosd]
 
 # set display size [default: 20x4]
 Size=20x4
 
-# font to use
-Font=-*-terminus-*-r-*-*-*-320-*-*-*-*-*
+# Offset in pixels from the top-left corner of the monitor [default: 0x0]
+Offset=200x200
+
+# X font to use, in XLFD format, as given by "xfontsel"
+Font=-*-clean-*-*-*-*-*-160-*-*-*-*-*-*
 
 # EOF